Daewoo DALLM18-320-1, User Manual

Page: 11 / 17

EN
11
While mowing, stay alert for any foreign objects which may have been missed. (Fig.6A)
2. Never lift the rear of the mower while starting the motor or during normal operation. (Fig.6B)
3. Never place your hands or feel underneath the underpan or into the rear discharge chute while the
motor is running. (Fig.6C)
7. STARTING
9.1 Starting
Start the motor as follows (Fig 7A,)
a. Insert the battery and key.
b. Press the safety push-button (1).
c. And meanwhile, pull the switch handle (2), and keep it in grasp.
If you release the switch handle, the motor will stop.
CAUTION! The blade starts turning as soon as the motor is started.
WARNING!
Cutting elements continue to rotate after the motor is switch off.
9.2 For the best results when mowing
Clear lawn of debris. Be sure that the lawn is clear of stones, sticks, wire or other foreign objects
which could be accidentally thrown out by the mower in any direction and cause serious personal
injury to the operator and others as well as damage to property and surrounding objects. Do not cut
5-4 Adjustment of handle height
The handle of lawn mower is adjustable, it can be suit for different people. (Fig. 5A)
When the cutting height is adjust at 20mm, the handle height can be adjust from 84cm to 98cm, 3
position. (Fig.5B,Fig.5C,Fig.5D)
WARNING: Make this adjustment only when the blade is stopped.
WARNING: Disconnect the electric cord from the power supply.
6. SAFETY PRECAUTIONS
a. Always operate with the deflector or grass catcher in the correct position.
b. Always stop the motor before removing the grass catcher or adjusting the height of cutting posi-
tion.
1. Before mowing, remove all foreign objects from the lawn which may be thrown by the machine.
5-2 Assembly the grass catcher
1. To fit: Raise the rear cover and hitch the grass catcher on rear of mower. (Fig.3A/Fig.3B/Fig.3C/-
Fig.3A1/Fig.3B1/Fig.3C1)
2. To remove: grasp and lift the rear cover, remove grass catcher.
IMPORTANT:
If the position of indicator opening is very dirty, the indicator will not inflate-in this case, clean the
position of indicator opening immediately.
5-3 Adjustment of cutting height
Apply to different height of grass, lawnmower can adjust height at 3 positions(20-35-50mm). Pls
adjust four wheels to the same lever to make the lawn mower steady.
4. TECHNICAL DATA
Power: 20 V
Drive style: Gears drive
Cutting width: 32 cm
Speed: 3500 rpm
No load running time: 40 Minutes
Cutting grass: about 20 Minutes
Cutting height: 20/35/50 mm
Brack: Electric brack
Wheels: front: 125 mm, Rear: 140 mm
Grass collection: 35 L
Handle angle: adjustable
Switch: Double wings for both hands easy operation.
5. ASSEMBLY
5-1 Assembly the folding handle
a. Fix the lower handlebars into the unit body with locking knobs as Fig. 2A,/Fig.2B/Fig.2C shown.
b. Connect the upper handle and the lower handle with the locking knob. (Fig.2D/Fig.2E/Fig.2F)
c. Attach the cable clamp to the position shown and then attach the cable (Fig.2G).
wet grass. For effective mowing do not cut wet grass because it tends to stick to the underside of
the deck preventing proper mowing of the grass clippings. Cut no more than 1/3 the length of the
grass. The recommended cut for mowing is 1/3 the length of the grass. Ground speed will need to
be adjusted so the clippings can be dispersed evenly into the lawn. For especially heavy cutting in
thick grass it may be necessary to use one of the slowest speeds in order to get a clean well mowed
cut. When mowing long grass you may have to cut the lawn in two passes, lowering the blade ano-
ther 1/3 of the length for the second cut and perhaps cutting in a different pattern than was used the
first time. Overlapping the cut a little on each pass will also help to clean up any stray clippings left
on the lawn. The mower should always be operated at full throttle to get the best cut and allow it to
do the most effective job of mowing. Clean underside of deck. Be certain to clean the underside of
the cutting deck after each use to avoid a build-up of grass, which would prevent proper mulching.
Mowing leaves. The mowing of leaves can also be beneficial to your lawn. When mowing leaves
make sure they are dry and are not laying too thick on the lawn. Do not wait for all the leaves to be
off the trees before you mow.
WARNING! if you strike a foreign object, stop the motor. Pull out the mains plug, thoroughly
inspect the mower for any damage and repair the damage before restarting and operating the
mower. Extensive vibration of the mower during operation is an indication of damage. The unit
should be promptly inspected and repaired.
8. BLADE
The blade is made of pressed steel. It will be necessary to reshape it frequently (with a grind wheel).
Ensure that it is always balanced (an unbalanced blade will cause dangerous vibrations). To check
for balance, insert a round rod through the central hole and support the blade horizontally. A balan-
ce blade will remain horizontal. If the blade is not balanced the heavy end will rotate downwards.
Reshape the heavy end until the blade is currently balanced. To remove the blade (1), unscrew the
blade screw (2).
and replace any parts, which are damaged.
When reassembling, make sure that the cutting edges face in the direction of the motor rotation.
The blade screw (2) must be torque to 20N.m.
WARNING!
For service, replace the blade
WARNING! Disconnect the electric cord from the power supply.
WARNING!
Protect hands by using heavy gloves or a rag to grasp the cutting blades when
replace the blade.
9. MAINTENANCE AND CARE
WARNING!
Before performing any Maintenance or cleaning work, Always pull out the mains plug!
Do not spray the unit with water. Ingress of water may destroy the Switch-plug combination unit and
the electric motor. Clean the unit with a cloth, hand brush, etc.
Expert inspection is required, do not make any adjustment by yourself, must contact to customer
Service centre:
a. If the lawn mower strikes an object.
b. If the motor stops suddenly
c. If the blade is bent (Do not align!)
d. If the motor shaft is bent (Do not align!)
e. If a short-circuit occurs when the cable is connected.
f. If the gears are damaged.
g. If the V-belt is defective.
h. Use only manufacturer’s recommended replacement parts and accessories.
10. TROUBLESHOOTING
WARNING!
before performing any maintenance or cleaning work, always pull out the mains plug
and wait until the cutter has come to a standstill
CAUTION! Faults which can not be rectified with the aid of this table may be rectified by a spe-
cialist company only (customer service centre).
11. ENVIRONMENTALLY FRIENDLY DISPOSAL
Fig. 8