background image

9

Installation Instructions

Verifying Proper Operation

 WARNING

Read the accompanying use and care manual completely 

before using the cooktop.

1.  Remove all items from the cooktop. Remove any tape 

that may be attached to the cooktop.

2.  Clean the cooking surface according to the use and 

care manual prior to use.

3.  Turn on power to the cooktop at the circuit breaker 

panel or fuse box. When the unit is powered on, the 

controls will automatically cycle on and then turn off.

4.  Place a pot 1/4 full with water on one of the cook-

ing elements. Match the size of the pot to the size of 

the cooking element. 

NOTE:

 You must use a pot that 

attracts a magnet on the pan bottom to test operation. 

5.  Hold your finger on the 

ON/OFF

 key for correspond-

ing control for one second to activate. The power light 

should come.

6.  Touch the power level 

UP

 key (▲) repeatedly. Verify 

that the power level goes up.

7.  Touch 

DOWN

 (▼) repeatedly. Verify that the power 

level goes down.

8.  Touch the power level 

UP

 key (▲) repeatedly until the 

power boost light comes on. 

9.  Once the pot begins to heat, verify that the heat indica-

tor light comes on.

10. Touch 

ON/OFF

 to turn off the element. 

11.  Repeat steps 4 through 10 for the remaining elements.

NOTE:

 If the cooktop does not operate properly, follow 

these troubleshooting steps:

◊ 

Verify that power is supplied to the cooktop.

◊ 

Check for proper electrical connections.

◊ 

Repeat the above tests.

◊ 

If the appliance still does not work, contact Dacor 

Distinctive Service at (800) 793-0093 ex. 2822. Do 

not attempt to repair the appliance yourself. If you 

need service, be sure to have the model and serial 

numbers available when you call. They are located 

on the label on the bottom of the appliance chassis.

Installation Checklist

 WARNING

• 

To ensure a safe and proper installation, the follow-

ing checklist should be completed by the installer to 

ensure that no part of the installation has been over-

looked.

• 

Proper installation is the responsibility of the home-

owner. The importance of proper installation of your 

Dacor cooktop cannot be overemphasized.

 

Have all minimum cabinet/countertop clearances been 

met or exceeded? See pages 4 and 5.

 

Is the cooktop wired and grounded according to these 

instructions and in accordance with all applicable elec-

trical codes and ordinances? See pages 3  

and 7.

 

Is the cooktop secured using the provided hold-down 

brackets? See page 7.

 

Has proper operation been verified?

 

Has the warranty been activated on-line or the warranty 

card filled out completely and mailed?

Cooktop Controls

Power 

light

Up key

ON/OFF 

key

DOWN 

key

Heat 

indicator

Power level 

indicators

Power 

boost light

No pan 

detected 

light

Summary of Contents for RNCT304













Reviews: