![background image](http://html.mh-extra.com/html/dacor/renaissance-rnrp30g/renaissance-rnrp30g_installation-instructions-manual_496421016.webp)
14
Verifying the Correct Setup
Before using the range, read the accompanying Use and Care
Manual completely. It contains Important safety, service, and
warranty information.
1. Before beginning this test procedure, ensure that all cooktop
control valves are
OFF
, and all burner rings, burner caps, and
grates are properly placed on the cooktop.
2. Turn the gas supply
ON
at the shut-off valve.
3. Plug the power cord into an electrical outlet. When the range
is first connected, the oven indicator light flashes for about 10
seconds while the range’s circuitry begins.
4. Wait for the light to stop flashing before going to Step 5.
IGNITION TEST:
5. Test a burner by pushing the knob and turning it to
HIGH
.
•
It may take up to FOUR seconds for ignition, at which time
the ignitor will stop sparking. If ignition does not occur within
FOUR seconds:
•
turn the knob to OFF, wait for at least five minutes to
allow any gas to dissipate, then repeat the ignition test.
6. After ignition, rotate the control
knob from
HIGH
to
LOW
to adjust
the flame.
When the range is correctly
installed, the flame will be steady
and quiet. It will also have a
sharp, blue inner cone that will
vary in length proportional to
the burner size. Dacor’s Smart
Flame™ feature reduces the
flame under the grate to increase
the life of the grate. If the range is equipped for
use with LP gas, the ends of the flame may be
yellow, which is normal.
7. Turn the control knob to
OFF
.
8. Repeat the ignition test for all the remaining
burners. After testing, turn them off.
9. Open the oven door(s). Test the oven light(s) by turning the
light switch(s) on the control panel.
10. Turn on the convection fan switch(s). You should hear the
convection fan, located behind the screen at the back of the
oven, come on.
11. With the oven door open, turn the oven temperature setting
to 400 °F. Both the knob and the oven ON indicator light next
to the knob should illuminate. Within 60 seconds, you should
hear the bake burner ignite below the oven floor. It should
begin to give off heat.
12. Turn the oven control knob to the BROIL position. The bake
burner should turn off. Both the oven control knob and the
oven ON indicator light should be illuminated.
13. Within 60 seconds the IR burner on the ceiling of the oven
should ignite and begin to give off heat.
14. Turn the oven knob to the OFF position.
If the range does not operate properly, follow these
troubleshooting steps:
1. Verify that power and gas are supplied to the range.
2. Check the electrical connections and gas supply to ensure
that the installation has been completed correctly.
3. Repeat the burner ignition test and/or oven test.
4. If the appliance still does not work, contact Dacor Distinctive
Service at (800) 793-0093 ex. 2822. Do not attempt to repair
the appliance yourself. Have the model and serial numbers
available when you call. See inside cover for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
Removing the Range for Service
1. Turn the gas supply valve to OFF.
2. Disconnect the power cord from the electrical outlet.
3. Pull the range out from the wall
Reinstalling the Range After
Service
1. Push the range into operating position, making sure the anti-
tip bracket is engaged (see page 11).
2. Connect the power cord to the electrical outlet.
3. Turn the gas supply valve ON.
OFF Icon
Correct Flame
Installation Instructions
Summary of Contents for Renaissance RNRP30G
Page 18: ...16 Notes ...
Page 19: ...Notes ...