background image

18

Before You Call for Service

Problem

May Be Caused By

What to Do

Nothing works.

Range not connected to electri-

cal power.

Check to make sure range power plug is 

connected to electrical outlet.

Power is off.

Turn on power at circuit breaker or fuse 

box for electrical outlet range is con-

nected to. Check for tripped breaker or 

blown fuse. 

Power outage.

Contact power company.

Igniters do not spark.

Power not supplied to unit.

See 

Nothing Works

 above.

Wet or dirty igniter.

Clean and dry igniter and burner assem-

bly according to 

Care and Cleaning

 

section.

No flame.

Igniter not working (no clicking 

sound).

See 

Igniters do not spark

 above.

Wet or dirty igniter.

Clean and dry according to 

Care and 

Cleaning

 section.

Gas is turned off.

Make sure the gas supply valve is in the 

“ON” position.

Gas supply interrupted.

Contact gas company.

Burner goes out at low set-

ting. 

Low gas pressure.

Contact gas company to have pressure 

tested.

Air intake holes obstructed.

Check to make sure none of the air slots 

on range are obstructed.

Flame is distorted, yellow or 

very large.

Burner parts are dirty or 

clogged.

Clean and dry according to 

Care and 

Cleaning

 section.

Burner parts are not properly 

positioned.

Make sure burner is assembled according 

to the 

Setting Up Your Range

 section.

Range set up to use a different 

type of gas (natural or LP) or 

set up for different altitude.

Have a qualified service technician check 

to make sure that the range is set up for 

the type of gas and the correct altitude.

Gas regulator is not installed or 

faulty.

Have a qualified service technician check 

the gas regulator.

Igniter continues to spark 

(click) after flame ignites.

Burner is cold.

Burners may continue to spark for up to 

60 seconds when cold and set to low. See 

Operating Your Range

 section for more 

information on how to minimize.

Flame distorted by air draft.

Minimize any air drafts around the cook-

top. Close nearby windows.

Wet or dirty igniter.

Clean and dry according to 

Care and 

Cleaning

 section.

Burner parts wet or dirty.

Clean and dry according to 

Care and 

Cleaning

 section.

Burner parts not properly posi-

tioned.

Make sure burner is assembled according 

to the 

Setting Up Your Range

 section.

Power supply polarity is 

reversed or not properly 

grounded.

Have a licensed electrician check the elec-

trical outlet.

Orange glow on ceiling of 

oven when broiling.

Normal operation.

The IR broil burner igniter glows orange 

off and on when the oven knob is set to 

broil.

Summary of Contents for Renaissance ER30G

























Reviews: