background image

3

Product Dimensions - ERV3015 and ERV3615

Product Specifications

15"

(38.1 cm)

30"

(76.2 cm)

20”

(50.8 cm)

1 1/8”

(2.9 cm)

28" 3 prong 

grounded

power cord

Motor

cover

Front of unit

6”

(15.2 cm)

2 9/16”

(6.5 cm)

9/16”

(1.4 cm)

3”

(7.6 cm)

1 15/16”

(4.9 cm)

 B

 A

2 1/8”

(5.4 cm)

2 3/16”

(5.6 cm)

3/16”

(5 mm)

5/16” (8 mm) 

thick stiffener 

across back

Top cap with 

vent down

Vent shown 

in raised 

position

3 3/4” 

(9.5 cm)

30 1/4”

(76.8 cm)

to

37 1/4”

(94.6 cm)

Adjustable 

anchor legs

Product 

data label

Tolerances: ±1/16” (±1.6 mm) unless otherwise stated

Model 

Number

A - top Cap  

Width

B - Chassis  

Width

ERV3015

30” (76.2 cm)

27 3/8” (69.5 cm)

ERV3615

36” (91.4 cm)

33 3/8” (84.8 cm)

See pages 9 and 

10 for exhaust 

locations  and 

dimensions.

** Maximum height of downdraft vent must not exceed maximum specified counter 

height for cooking appliance. See installation instructions for cooking appliance.

* Total chassis depth with optional CABP3 blower installed is 10 3/8” (26.3 cm).

*

**

2 1/8" (5.4 cm)

3/8"

(1.0 cm)

2 1/8" (5.4 cm)

ERV top cap - side view

PRV top cap - side view

7/16"

(1.1 cm)

Summary of Contents for ERV3015





















Reviews: