background image

14

Installation Instructions

Cabinet Blower Installation:

(optional, ERV3015 and ERV3615 only)

1.  Locate the wiring diagram label included with the 

adapter kit. Peel the protective backing off and place it 

over the existing label on the CABP3 blower as shown.

2.  Locate the foam tape supplied with the downdraft vent. 

Place the blower on the floor in the orientation it will be 

mounted on the front of the downdraft vent. Peel the 

backing off the included foam tape and attach it to the 

right and left flanges of the blower base plate.

3.  With the exhaust in the desired orientation, slide the 

bottom flange of the CABP3 blower base plate behind 

the tab on the bottom of the adapter mounted to the 

front of the downdraft vent.

4.  Cover the opening on the adapter by pushing the 

blower against it. Make sure that the foam tape cre-

ates a good seal on the right and left side of the open-

ing. Center the blower base plate horizontally over the 

opening on the front of the adapter. 

5.  Install the adapter top retainer bracket over the blower 

base plate flange. Secure it in place with the three (3) 

wing nuts, lock washers and flat washers included with 

the adapter.

CABP3

Top retainer 

bracket

Insert bottom flange into 

tab at bottom of adapter 

Attach foam

to right/left

flanges

Adapter

New label

Existing 

label

ILHSF or REMP Series Blower Installation

If using a ILHSF or REMP series blower, install it according 

to the blower installation instructions.

Duct Work Installation

 WARNING

Tape all duct joints securely to prevent combustion 

by-products, smoke or odors from entering the home. 

Doing so will also improve system efficiency.

Install the duct work according to the 

Installation 

Specifications

 section. Use sheet metal screws and duct 

tape to connect and seal all of the pieces. Support the duct 

weight as necessary to ensure sealed joints.

Electrical Installation

 WARNING

• 

ELECtRIC SHOCK HAZARD

 - Do not connect the 

downdraft vent power plug to the electrical outlet until 

installation is complete.

•  Failure to complete electrical connections properly 

may result in an electric shock hazard or a damaged 

or non-functional system. Follow the wiring diagrams 

carefully to ensure a proper installation. Do not 

change the factory wired terminal connections inside 

the electrical access panel for the downdraft vent or 

the blower.

•  To avoid an electric shock hazard and to prevent dam-

age route all wiring away from hot surfaces.

1.  For ILHSF and REMP blower installations, run the wir-

ing/conduit line used to supply power from the down-

draft vent to the blower parallel to the duct work.

2.  Remove the cover from the downdraft vent electrical 

access panel. 

3.  Connect the wiring/conduit to the blower as shown in  

the wiring diagrams below and the facing page accord-

ing to local codes and ordinances. Make sure all ter-

minal connections, including the factory wired connec-

tions, are tight. Replace the electrical access panel.

Range/Cooktop Installation

Install the range or cooktop according to its installation 

instructions. 

Summary of Contents for ERV3015





















Reviews: