background image

 Page 5-2

D

aCor

 b

uilT

-i

n

 D

ishwasher

 s

erviCe

 M

anual

SYMPTOM

 

CHECK THE FOLLOWING

 

REMEDY

 

Dishwasher will not  
pump out.

1. Drain restricted.

 

2. Defective drain pump. 
3. Air lock in drain hose.

 

4. Blocked impeller. 
5. Open windings. 
6. Wiring or terminal defective.

 

7. Electronic control board

  

   

 defective.

 

1. Clear restrictions. 
2. Replace pump 
3. Check dishwasher installation.

 

4. Check for blockage and clear.

 

5. Replace windings. 
6. Repair or replace. 
7. Replace control board.

 

Dishwasher will not fill

 

with water.

 

1. Water supply turned off. 
2. Defective water inlet valve. 
3. Check fill valve screen for

  

    

obstructions. 

4. Defective pressure switch. 
5. Electronic control board  

   

defective

.

6. Wiring or terminal defective.

 

1. Turn water supply off. 
2. Replace water inlet fill valve. 
3. Disassemble and clean screen.

 

4. Repair or replace. 
5. Check/replace control board. 

6. Repair or replace.

 

Dishwasher water  
siphons out.

1. Drain line connected to a floor

 

    

drain not vented.

 

1. Install air gap at counter top.

 

Detergent left in 
dispenser.

1. Detergent allowed to stand too

  

 

   long in dispenser. 

2. Dispenser wet when detergent

 

    

was added.

 

3. Detergent cover held closed or

 

    

blocked by large dishes.

 

4. Improper incoming water

  

    

temperature to properly

  

   

dissolve detergent. 

5. See

 

“Detergent Cover Will Not 

    

Open”

.

1. Instruct customer/user.

 

2. Instruct customer/user. 

3. Instruct customer/user on

  

    

proper loading of dishes.

 

4. Incoming water temperature of

  

    

120°F is required to properly  

    

dissolve dishwashing detergent. 

Summary of Contents for Built-In Dishwasher



































Reviews: