background image

 Page 5-1

s

eCTion

 5 - T

roubleshooTing

 T

iPs

SYMPTOM

 

CHECK THE FOLLOWING

 

REMEDY 

Dishwasher will 

not operate when
turned on.

 

1. Fuse (blown or tripped).

 

2. 120 VAC supply wiring 

 

    

connection faulty.

 

3. Electronic control board

 

 

   

faulty.

 

4. Motor (inoperative, check

  

   

 

resistances).

 

5. Door switch (open contacts).

 

6. Door latch not making 

 

    

contact with door switch.

 

7. Touch pad circuit defective.

 

8. No indicator lamps illuminate

  

    

when START or OPTIONS is 

   

depressed. 

1. Replace fuse or reset breaker

2. Repair or replace wire

  

    

fasteners at dishwasher

  

    

junction box.

 

3. Replace control board.

 

4. Replace motor/impeller

  

    

assembly

5. Replace door switch.

 

6. Replace latch assembly.

 

7. Replace keypad.

 

8. Replace keypad.

 

Motor hums but will not

 

start or run.

 

1. Motor (bad bearings or locked

  

   

 rotor)

2. Motor locked due to prolonged

 

  

  non-use.

 

1. Replace motor. 

2. Rotate motor fan or impeller.

 

Motor trips out on 

 

internal thermal 
overload protection. 

1. Improper voltage. 
2. Seal faces binding.

 

3. Motor windings shorted.

 

4. Glass or foreign items in pulp. 

1. Check voltage. 
2. Rotate motor fan or impeller, or

  

   

 replace.

 

3. Replace motor/pump assembly.

 

4. Clean and clear blockage.

 

Dishwasher runs but 

 

will 

not heat.

 

1. Heater element open.

 

2. Electronic control board

  

   

defective.

 

3. Wiring or terminal defective.

 

1. Replace heater element.

 

2. Replace control board.

 

3. Repair or replace.

 

Detergent cover will 

 

not latch or open. 

1. Excess detergent on lid catch.

 

2. Latch mechanism defective.

 

3. Electronic control board 

 

   

defective.

 

4. Wiring or terminal defective.

 

5. Broken spring(s). 
6. Defective actuator.

 

1. Clean catch area.

 

2. Replace dispenser. 
3. Replace control board.

 

4. Repair or replace. 
5. Replace dispenser. 
6. Replace actuator.

 

Summary of Contents for Built-In Dishwasher



































Reviews: