background image

 Page 4-6

s

eCTion

 4 - s

erviCe

 & D

isasseMbly

Water Valve

Disconnect dishwasher from power supply.
Turn off water supply to dishwasher.
Remove kick plate and lower access panel. Removal of outer door panel may be needed to gain 

access to necessary parts.
Remove wire connect and water supply line. 
Remove two mounting screws holding water valve to front frame.
To remove fill hose from valve, rotate water valve. Then remove valve.
Reverse procedure to reinstall.

CABINET REMOVAL

Disconnect power supply and water supply.
Remove drain hose from drain line.
Slide dishwasher from under countertop to gain access to cabinet.
Remove four screws mounting top trim to tub. Also remove screws on each side that secure lower 

trims to cabinet.
Remove screws from front flange of cabinet that attach it to tub. (See Figure 34)
From rear of cabinet, remove screws that attach it to rear frame. (See Figure 36)
Lay dishwasher on its back on a protective pad. Remove screws that attach the cabinet to bottom of 

frame. (See Figure 35)
Open sides of cabinet and slide cabinet away from tub. 

 

CAUTION

1.
2.
3.

4.
5.
6.
7.

1.
2.
3.
4.

5.
6.
7.

8.

 

 Edges are sharp. Protect yourself and  

be careful not to damage the insulation  

blanket around the tub.

FROnT OF CABInET 

– FIgURE 34

BOTTOM OF DISHWASHER 

– FIgURE 35

BACK OF CABInET 

– FIgURE 36

Summary of Contents for Built-In Dishwasher



































Reviews: