background image

16

EQUIPMENT REUSE

The equipment can be reused in undetermined, i.e. unlimited, quantities, only needing to be cleaned,

disinfected and Sterilization.

Cleaning and Disinfection

These processes should be used in the handpieces.

Uncouple the piece from the INTRA fit terminal.

Remove the diamond tip or bur.

Clean the external surface with neutral soap and using a clean and soft cloth.

Do  not  use  microabrasive  material  or  steel  wool  when  cleaning,  or  employ  organic  solvents 

ordetergents which contain solvents such as ether, stain remover, etc.

Warning 

Never submerge the instrument in a disinfection bath.

Never use product peracetic acid for cleaning, since it is corrosive.

For your protection, during the equipment cleaning and disinfection process, use PPE such

as disposable gloves and goggles.

The cleaning and disinfection process must be performed at each patient change.

When starting the process, check for visible dirt, such as blood or saliva.

For cleaning use a clean, soft cloth moistened with mild soap and then dry with a clean, soft cloth

or paper towel.

For the disinfection process of the Handpiece, use disinfectant detergent foam without alcohol that 

has active components based on didecyldimethylammonium chloride.

Apply the disinfectant detergent foam on the surface or on a clean cloth and spread it on the surface

to be treated. Respect the antimicrobial contact time specified by the manufacturer.

Additional procedures for reuse

Warning 

Handpieces may only be serviced in the field at the points described in the user manual. If

they need to be disassembled, they must be taken to the manufacturer.

Sterilization

Follow the instructions of the manufacturer of the appliance.

Only sterilize clean and lubricated handpieces.

Clean, grease and remove the overflow oil in the apparatus according to the previous indicate, 

put it in the surgical grade paper (not provided by Alliage) and sterilize it in autoclave until 135°C

(275°F) through a cycle.

Warning 

Sterilize before 1st use, product do not provided sterilized.

Not valid or recommend to the sterilization by ethilene oxyde.

Do not sterilize in an oven.

Before sterilization, connect it to the delivery unit and activate it for a few seconds to 

eliminate the excess of oil.

If the excess of oil is not eliminated, it may cause burnt residue in the bearing.

They should be sterilized only in an autoclave at 135ºC with at least 3 minutes of waiting

time and with a pressure of 2.2 bar.

Summary of Contents for COBRA CONTRA ANGLE INTRA 32 CA





















Reviews: