background image

ENGLISH 

19 

 

Example 1: installation at sea level and fluid at t = 20°C 

Required N.P.S.H. : 

3.25 m 

Pb : 

10.33 mcw 

Hr: 

2.04 m 

t: 

20°C 

PV: 

0.22 m  

Z1

 

10.33 - 3.25 - 2.04 - 0.22 = 4.82 approx. 

Example 2: installation at a height of 1500 m and fluid at t = 50°C 

required N.P.S.H. : 

3.25 m 

pb : 

8.6 mcw  

Hr: 

2.04 m 

t: 

50°C 

pV: 

1.147 m  

Z1

 

8.6 - 3.25 - 2.04 - 1.147 = 2.16 approx. 

Example 3:  installation at sea level and fluid at t = 90°C 

required N.P.S.H. : 

3.25 m 

pb : 

10.33 mcw  

Hr: 

2.04 m 

t: 

90°C 

pV: 

7.035 m  

Z1

 

10.33 - 3.25 - 2.04 - 7.035 = -1.99 approx. 

In the last case, in order to operate correctly the pump must be fed with a positive head of 1.99 - 2 m, that is the free surface of the water must 

be 2 m higher than the axis of the pump. 

 

 

 

N.B.: it is always good practice to leave a safety margin (0.5 m in the case of cold water) to allow for errors or unexpected 

variations in the estimated data.  This margin becomes especially important with liquids at a temperature close to boiling 

point, because slight temperature variations cause considerable differences in the working conditions.  For example in 

the third case, if instead of 90°C the water temperature reaches 95°C at any time, the head required by the pump would 

no longer be 1.99 but 3.51 metres.

 

7.4.  Connecting auxiliary systems and measuring instruments.

 

The realization and connection of any auxiliary systems (washing liquid, seal cooling fluid, dripping liquid) must be considered when 

designing the system. These connections are necessary for better and longer lasting pump operation. 

In order to ensure continuous monitoring of the pump functions, it is recommended to install a vacuum pressure gauge don the intake 

side and a pressure gauge on the delivery side. To check the motor load the installation of an ammeter is advised.

 

 

8. 

ELECTRICAL CONNECTION 

 

 

Scrupulously follow the wiring diagrams inside the terminal board box and those on page 1 of this manual.

 

8.1. 

In the case of three-phase motors with star-delta start, ensure that the switch-over time from star to delta is as short as possible and 

that it falls within table 8.1 on page 105.

 

8.2. 

Before opening the terminal board and working on the pump, ensure that the 

power has been switched off

.

 

8.3. 

Check the mains voltage before making any connection.  If it is the same as the voltage on the data plate, proceed to connect the wires 

to the terminal board, 

giving priority to the earth lead. 

8.4. 

The pumps must always be connected to an external switch.

 

8.5. 

The motors must be protected with special remote-control motor-protectors calibrated for the current shown on the plate.

 

 

9. 

STARTING UP 

9.1. 

 

Before starting the pump, check that: 

 

the pump has been properly primed, filling the pump body completely. This ensures that the pump immediately starts to 

work regularly and that the seal (mechanical seal or stuffing box seal) is well lubricated. 

Dry operation causes 

irreparable damage to the mechanical seal and the stuffing box seal.

 

 

the auxiliary circuits have been correctly connected; 

 

all the moving parts have been protected with suitable safety systems; 

 

the electrical connection has been made as indicated previously; 

 

10. 

STARTING/STOPPING 

10.1.  STARTING 

10.1.1. 

Fully open the gate valve on intake and keep the one on delivery almost closed. 

10.1.2. 

Switch on the power and check that the motor is turning in the right direction, that is clockwise when viewed from the fan side. This 

check must also be performed after having fed the pump, activating the main switch with a fast start-stop sequence. If the motor is 

turning in the wrong direction, invert any two phase leads, after having disconnected the pump from the mains. 

10.1.3. 

Once the hydraulic circuit has been completely filled with liquid, gradually open the delivery gate valve until its maximum allowed 

opening. The motor's energy consumption must be checked and compared with the value shown on the data plate, 

especially in 

cases where the pump has intentionally been given a reduced power motor (check the design characteristics)

10.1.4. 

With the pump running, check the supply voltage at the motor terminals, which must not differ from the rated value by +/- 5% 

 

 

 

 

 

 

 

Summary of Contents for NKM 32-125





















Reviews: