background image

2

1.  Carefully unpack screen and remove outer wrapping from case.

2.  Do not remove black tape or rubber bands from slat pocket.

3.  Always handle screen in horizontal position.

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1.  Read and understand all instructions before using.

2.  Maximum surrounding air temperature 122°F (50°C).

3.  Main disconnect must be incorporated in the fixed wiring in 

accordance with the wiring rules.

4.  Rated for indoor use only.

5.  Use copper rated conductors rated 167°F (75°C) or higher.

6.  If the supply cord is damaged, it must be replaced by the 

manufacturer, its service agent or similarly qualified persons in 
order to avoid hazard.

7.  Supplied drive is only intended for use in Da-Lite screen models 

Advantage, Contour, and Cosmopolitan.

8.  Position the cord so that it will not be tripped over, pulled, or 

contact hot surfaces.

9.  If an extension cord is necessary, a cord with a current rating at 

least equal to that of the appliance should be used. Cords rated 
for less amperage than the appliance may overheat.

10.  To reduce the risk of electric shock, do not disassemble this 

appliance. Contact an authorized service dealer when repair 
work is required. Incorrect reassembly can cause electric shock 
when the appliance is used subsequently.

11.  The use of an accessory attachment not recommended by the 

manufacturer may cause a risk of fire, electric shock, or injury to 
persons.

12.  Failure to provide adequate structural strength for this 

component can result in serious personal injury or damage to 
equipment! It is the installer’s responsibility to make sure the 
structure to which this component is attached can support the 
weight of all equipment. Reinforce the structure as required 
before installing the component.

13.  Use this projection screen only for its intended use as described 

in these instructions. Do not use attachments not recommended 
by the manufacturer.

Save These Instructions

Pre-Installation 

Original Instructions

Disclaimer

Milestone and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. 
However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide 
for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any 
kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone 
assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies. All rights reserved.

Summary of Contents for Cosmopolitan Electrol

















Reviews: