background image

84214

FOR YOUR IMAGE  |  legrandav.com

USA P

 866.977.3901 

E

 [email protected] 

CANADA P

 877.345.4329 

[email protected] 

EMEA P

 +31 495 580 840 

E

 [email protected] 

APAC P 

+852 2145 4099 

[email protected]

In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone AV Technologies ULC. 
©2018 Milestone AV Technologies. DL–0113  (Rev. 6)  8/18 Da-Lite is a registered trademark of Milestone AV 
Technologies. All other brand names or marks are used for identification purposes and are trademarks of 
their respective owners. All patents are protected under existing designations. Other patents pending. 

LIMITED FIVE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in 
materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly 
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the 
factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered 
with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. 
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, 
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.  
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY.

 Any implied warranties of fitness for use, 

or merchantability, that may be mandated by statute or rule of law are limited to the five (5) year warranty period. This warranty gives 
you specific legal rights, and you may also have other rights, which vary from state-to-state. 

TO THE MAXIMUM EXTENT PERMITTED 

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION 
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at 
3100 North Detroit Street, Warsaw, IN 46582, (574) 267-8101, (800) 622-3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS 
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Summary of Contents for ADVANTAGE ELECTROL

















Reviews: