background image

5

Screen and Roller Assembly Installation

Motor Mount 
Bracket

Motor Power 
Connector

1/4-20 Nuts

Access Door Screws

Foam Blocks 

Pin End

Figure 1

Motor End

Follow these steps if your screen and roller assembly was ordered separately from the case.

1.   Remove the access door. First, remove the 2 screws from the 

ends. Be sure to support the door during this step to avoid 
injury. Then lift the door slightly and pull away from the edge 
of the case (Figure 1).

2.   Carefully unpack screen and roller assembly. Leave packing 

paper on roller.

3.   To install screen and roller assembly, loosen (but do not 

remove) four 1/4-20 nuts securing pin end bracket (opposite 
end from the junction box) to the case housing. Slide the pin 
end bracket towards the end of the case (Figure 2).

4.   Insert the motor end square shaft into the motor end bracket 

(junction box end) and secure with the cotter pin. (Figure 2).

5.   Moving to the pin end of the case, slide the pin end bracket 

until the hole fits securely over the pin and secure with the 
cotter pin. Tighten the 1/4-20 nuts on the pin end bracket 
securely (Figure 2).

6.   Complete electrical hook-up by snapping motor wire 

connector into case connector (Figure 2).

7.   Carefully remove paper and tape from roller assembly. 

DO NOT use a knife or sharp object to cut tape; you will 
damage the screen. Pull orange string.

8.   Test installation by running screen up and down a few times. 

Be prepared to stop screen should any objects obstruct the 
movement of the screen. To prevent damage to the motor, 
the standard duty cycle is 1 minute on and 3 minutes off.

9.   Re-install the access door. Procedure is the reverse of step 1  

listed above.

Cotter Pins

Motor

Figure 2

Summary of Contents for ADVANTAGE ELECTROL

















Reviews: