background image

 

 

d.s.f. GmbH BZ – V 24 TK Version 11/2021 

Page 

10 of 10 

9.  

Delivery conditions 

 
Deliveries will basically be made on the basis of our General Terms and Conditions. 

 

10.   Storage 

 
To maintain the full power supply of the lead-gel-battery in the ignition device, the products should 
not be stored for more than 24 months without a new charge. It is recommended to maintenance 
charge the battery every 6 months using the charger supplied. (See chapter

 

4) 

 
 

Please note: 

 

The spark gap and the high-energy spark plug are wear parts and thus exempted from the  

warranty, since their service life depends on the number of ignitions and the conditions of use.  

 

11. 

Warranty 

From the day of delivery, we accept the warranty for a period of 24 months to eliminate possibly 
errors or defects may cause an exchange. Requirement is, that an error can be attributed to defects 
in components or manufacture.  
The warranty is void if procedures are performed by the user or by third parties that is not expressly 
authorized in writing by us. 
 
Repairs will be done exclusively in our own repair shop. We do not accept repair bills from others. 
The delivery of faulty equipment at d.s.f. GmbH must be freight free. 
 

12. 

Liability 

We are not liable for consequential damages of any nature, which may arise in combination with 
any of our products. For any claims resulting from the failure to comply with this instruction manual, 
d.s.f. GmbH will also not be liable in any way. 

 

 

 

 

 

 

 

Subject to changes and modifications in the sense of the technical progress without prior 
notice. 
 

 

d.s.f. GmbH 

Spessartstraße 11 

D-63263 Neu-Isenburg 

Tel49 (0) 6102 / 7890-0 

T49 (0) 6102 / 7890-40 

E-mail: [email protected] 

www.dsf-gmbh.de 

 

Summary of Contents for BZ - V 24 TK











Reviews: