D-Link Wireless VPN Router DI-824VUP Factory Default Settings Download

Page: 46 / 55

146

Frequently Asked Questions (continued)

How do I configure my DI-824VUP to play Warcraft 3?

To hose a Warcraft 3 game, you must open ports on your router to allow incoming
traffic. To play a game, you do not have to configure your router.

Warcraft 3 (Battlenet) uses port 6112.

For the DI-824VUP:

Step 1

Open your web browser and

enter the IP Address of your router
(192.168.0.1). Enter username
(admin) and your password (leave
blank).

Step 2

Click on

Advanced

and

then click

Virtual Server

Step 3

Create a new entry: Click

Enabled

. Enter a name (warcraft3).

Private IP - Enter the IP Address of
the computer you want to host the
game. Select

Both

for Protocol Type

Enter

6112

for both Private Port and Public Port Click

Always

or set a schedule.

Step 4

Click

Apply

and then

Continue

Note:

If you want multiple computers from you LAN to play in the same game that you

are hosting, then repeat the steps above and enter the IP Addresses of the other
computers. You will need to change ports. Computer #2 can use port 6113, computer
#3 can use 6114, and so on.

You will need to change the port information within the Warcraft 3 software for
computers #2 and up.

Configure the Game Port information on each computer:

Start Warcraft 3 on each computer, click

Options

Gameplay

. Scroll down and you

should see

Game Port

. Enter the port number as you entered in the above steps.

Summary of Contents for Wireless VPN Router DI-824VUP
























































Search results

Summary of Contents for Wireless VPN Router DI-824VUP

Reviews:

Related manuals for Wireless VPN Router DI-824VUP

Brands by name

Popular brands

D-Link Wireless VPN Router DI-824VUP, Factory Default Settings

Search results

Summary of Contents for Wireless VPN Router DI-824VUP

Reviews:

Related manuals for Wireless VPN Router DI-824VUP

Brands by name

Popular brands