D-Link Wireless VPN Router DI-824VUP Factory Default Settings Download

Page: 12 / 55

112

Frequently Asked Questions (continued)

How can I setup my DI-824VUP to work with a cable modem
connection? (continued)

Step 3

Power cycle the cable modem and router:

First turn the cable modem off. Then turn the router off Leave them off for 2 minutes.**
Next turn the cable modem on. Wait until you get a solid cable light on the cable
modem, and then turn the router on. Wait 30 seconds.

** If you have a DCM-201modem, leave off for at least 5 minutes.

Step 4

Follow step 1 again and log back into the web configuration. Click the

Status

tab and click the

Device Info

button. If you do not already have a public IP Address

under the

WAN

heading, click on the

DHCP Renew

and

Continue

buttons.

Static Cable Connection

Step 1

Log into the Web-based configuration by typing in the IP address of the router

(default:192.168.0.1) in your Web browser. The username is

admin

(all lowercase) and

the password is blank (empty).

Step 2

Click the

Home

tab and click the

WAN

button. Select

Static IP Address

and enter your

static settings obtained from the ISP in the fields
provided.

If you do not know your settings, you must
contact your ISP.

Step 3

Click on

Apply

and then

click

Continue

to save the changes.

Step 4

Click the

Status

tab and

click the

Device Info

button. Your

IP Address information will be
displayed under the

WAN

heading.

Summary of Contents for Wireless VPN Router DI-824VUP
























































Search results

Summary of Contents for Wireless VPN Router DI-824VUP

Reviews:

Related manuals for Wireless VPN Router DI-824VUP

Brands by name

Popular brands

D-Link Wireless VPN Router DI-824VUP, Factory Default Settings

Search results

Summary of Contents for Wireless VPN Router DI-824VUP

Reviews:

Related manuals for Wireless VPN Router DI-824VUP

Brands by name

Popular brands