D-Link Wireless VPN Router DI-824VUP Factory Default Settings Download | Manualshive

Page: 14 / 55

background image

114

Step 8

Click

Apply

. When prompted, click

Continue

. Once the screen refreshes,

unplug the power to the D-Link Router.

Step 9

Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem

has established a link to your ISP, plug the power back into the D-Link Router. Wait
about 30 seconds and log back into the router.

Step 10

Click on the

Status

tab in the web configuration where you can view the

device info. Under

WAN

, click

Connect

. Click

Continue

when prompted. You should

now see that the device info will show an IP Address, verifying that the device has
connected to a server and has been assigned an IP Address.

How can I setup my DI-824VUP to work with Earthlink DSL or any
PPPoE connection? (continued)

Frequently Asked Questions (continued)

Can I use my DI-824VUP to share my Internet connection provided by
AOL DSL Plus?

In most cases yes. AOL DSL Plus may use PPPoE for authentication bypassing the
client software. If this is the case, then our routers will work with this service. Please
contact AOL if you are not sure.

To set up your router:

Step 1

Log into the Web-based configuration (192.168.0.1) and configure the WAN

side to use PPPoE.

Step 2

Enter your screen name followed by @aol.com for the user name. Enter your

AOL password in the password box.

Step 3

You will have to set the MTU to 1400. AOL DSL does not allow for anything

higher than 1400.

Step 4

Apply settings.

Step 5

Recycle the power to the modem for 1 minute and then recycle power to the

router. Allow 1 to 2 minutes to connect.

If you connect to the Internet with a different Internet Service Provider and want to use
the AOL software, you can do that without configuring the router’s firewall settings.
You need to configure the AOL software to connect using TCP/IP.
Go to

http://www.aol.com

for more specific configuration information of their software.

«
...
12
13
14
15
16
...
»

Summary of Contents for Wireless VPN Router DI-824VUP
























































Reviews:

No comments

Related manuals for Wireless VPN Router DI-824VUP

Brand: D-Link Pages: 61

Brand: Ebyte Pages: 14

LTE Mobile HotSpot PRO

Brand: Samsung Pages: 77

Brand: macaroon Pages: 13

Brand: NetComm Wireless Pages: 2

Brand: H3C Pages: 43

11b/g Wireless Outdoor Multi-Client Bridge/AP

Brand: EnGenius Pages: 53

Brand: OBERON Pages: 2

Brand: Aruba Pages: 2

YLS0056A-E080040

Brand: THOMSON Pages: 38

Brand: Cambium Networks Pages: 51

Brand: Kogan Pages: 16

Juplink RX4-1500

Brand: Vanin Pages: 2

Brand: CreatComm Pages: 40

Brand: Avaya Pages: 425

Brand: Wieland Pages: 33

Brand: 4IPNET Pages: 15

Brand: 4IPNET Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands