D-Link DVG-3032S User Manual Download Page 68

Page: 68 / 69

DVG-3032S/3016S User’s Manual

Appendix

D-Link Systems, Inc.

Appendix

Product Features

WAN



One 10/100Mbps auto-negotiation, auto-crossover RJ-45 Ethernet port



Support static IP, PPPoE and DHCP address assignment and dynamic DNS (DDNS)



QoS: IP TOS (Type of Services) and DiffServ (Differentiated Services) for both SIP
signaling and RTP



NAT Traversal : STUN and Outbound Proxy



NTP: (Network Time Protocol RFC 1305)



Time Zone Support



MAC Address Clone



RTP Packet Summary: packet sent, packet received, packet loss for voice quality analysis

LAN



One 10/100Mbps auto-negotiation, auto-crossover RJ 45 Ethernet port



Supports router and bridge mode



DHCP server

Voice Features



SIP (RFC3261) compatible



Voice codecs : G.711 a /u law, G.726, G.729A, G.723.1



CNG (Comfort Noise Generation)



VAD (Voice Activity Detection)



G.165/G.168 echo cancellation



Adjustable Jitter Buffer and programmable Gain Control



In-Band DTMF, Out-Of-Band DTMF relay (RFC2833, SIP INFO)



Multiple SIP Proxy server entries with failover mechanism



Polarity reversal generation



T.30 (G.III) / Real time T.38 / Secured T.38 FAX relay



DTMF, FSK (Bellcore ,ETSI and NTT) Caller ID generation.



Support Caller ID Restriction (CLIR)



Digit Map for dial plan



Speed Dial



Local phone book for peer-to-peer calling



E.164 Numbering & ENUM support



Hot-Line, Warm-Line support



Single Number / Account (reprehensive number) for multiple ports



Call features:

Call Forward - Unconditional, Busy



Analogue interface

Connector: RJ-21

Signaling protocol : Loop Start

Summary of Contents for DVG-3032S






































































Search results

Summary of Contents for DVG-3032S

Reviews:

Related manuals for DVG-3032S

Brands by name

Popular brands

D-Link DVG-3032S, User Manual

Search results

Summary of Contents for DVG-3032S

Reviews:

Related manuals for DVG-3032S

Brands by name

Popular brands