D-Link DSL-2880AL User Manual Download Page 82

Page: 82 / 122

Section 3 - Configuration

D-Link DSL-2880AL User Manual

BUDGET QUOTA

Budget Quota

is a traffic meter feature offers



Traffic quota metering on the user specified interface over the user defined period



Traffic quota metering in different direction (both ingress and egress direction)



Interface locking down in order to prevent traffic over flow.

Budget Quota is designed mainly for user who subscribe non flat rate internet access plan. To prevent download traffic over monthly quota, user
can specify the WAN interface and download traffic quota.

Budget Quota

To access the

Budget Quota

window, click on the

Budget Quota

button

under the

ADVANCED

tab.

Please tick

Enable

Limitation

Quota

to activate Budget Quota

Select interface

to limit the data transmission quota.

Set meter duration over

Limit time(days)

Check

Enable Download quota

and set

Download quota(Max, GB)

Check

Enable Upload quota

and set

Upload quota(Max, GB)

Remark:



Before you activated Budget Quota, you MUST activate NTP and

have device sytem time adjusted accurately



Before you configure Budgt Quota, please have your WAN inteface

connected (otherwise, the WAN interface will not show over the
Budget Quota interface option)

Summary of Contents for DSL-2880AL



























































































































Search results

Summary of Contents for DSL-2880AL

Reviews:

Related manuals for DSL-2880AL

Brands by name

Popular brands

D-Link DSL-2880AL, User Manual

Search results

Summary of Contents for DSL-2880AL

Reviews:

Related manuals for DSL-2880AL

Brands by name

Popular brands