D-Link DSL-2880AL User Manual Download Page 22

Page: 22 / 122

Section 3 - Configuration

D-Link DSL-2880AL User Manual

SETUP

This chapter is concerned with using your computer to configure the WAN connection. The following chapter describes the various windows used to
configure and monitor the Router including how to change IP settings and DHCP server setup.

INTERNET SETUP

To access the

INTERNET SETUP

(WAN) settings window, click on the

Internet Setup

button in the

SETUP

directory in this page:

INTERFACE SETUP:

ADSL INTERFACE

Click on the

Setup

button located over ADSL INTERFACE if you want to

configure ADSL Interface WAN.

ETH INTERFACE

Click on the

Setup

button located over ETHERNET WAN INTERFACE if

you want to configure Ethernet WAN.

Summary of Contents for DSL-2880AL



























































































































Search results

Summary of Contents for DSL-2880AL

Reviews:

Related manuals for DSL-2880AL

Brands by name

Popular brands

D-Link DSL-2880AL, User Manual

Search results

Summary of Contents for DSL-2880AL

Reviews:

Related manuals for DSL-2880AL

Brands by name

Popular brands