D-Link DI-804 User Manual Download Page 72

Page: 72 / 75

adequate measures

Warnung!

Dies ist in Produkt der Klasse B. Im Wohnbereich kann dieses Produkt

Funkstoerungen verursachen. In diesem Fall kann vom Benutzer verlangt

werden, angemessene Massnahmen zu ergreifen.

Advertencia de Marca de la CE

Este es un producto de Clase B. En un entorno doméstico, puede causar

interferencias de radio, en cuyo case, puede requerirse al usuario para que

adopte las medidas adecuadas.

Attention!

Ceci est un produit de classe B. Dans un environnement domestique, ce

produit pourrait causer des interférences radio, auquel cas l`utilisateur

devrait prendre les mesures adéquates.

Attenzione!

Il presente prodotto appartiene alla classe B. Se utilizzato in ambiente

domestico il prodotto può causare interferenze radio, nel cui caso è possibile

che l`utente debba assumere provvedimenti adeguati.

FCC Warning

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 o f the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

Summary of Contents for DI-804












































































Search results

Summary of Contents for DI-804

Reviews:

Related manuals for DI-804

Brands by name

Popular brands

D-Link DI-804, User Manual

Search results

Summary of Contents for DI-804

Reviews:

Related manuals for DI-804

Brands by name

Popular brands