D-Link DI-804 User Manual Download Page 51

Page: 51 / 75

The unit is not receiving the correct voltage from the power supply.

Resolution:

Download and upgrade the latest firmware.

Make sure the correct firmware has been used while upgrading. Use only

the firmware provided on D-Link’s web or FTP sites.

Use only the power adapter provided.

The Link or Act LED’s do not turn on.

Cause:

The network cable is not connected.

The network cable is connected but not the right type, whether it is patch

or straight-through.

Resolution:

Make sure that both ends of the cable are connected.

Try using another cable.

If you are using a straight-through cable, try a patch cable and

vice-versa.

Sometimes my Broadband Router stops working or locks up.

Cause:

Someone has attempted to hack into someone on your LAN.

The Broadband Router has detected harmful data trying to access your

LAN.

The NAT table is full.

Resolution:

Reboot the Broadband Router by turning the power to the unit off and

then on again. Some types of hacker tools use very non-standard data

Summary of Contents for DI-804












































































Search results

Summary of Contents for DI-804

Reviews:

Related manuals for DI-804

Brands by name

Popular brands

D-Link DI-804, User Manual

Search results

Summary of Contents for DI-804

Reviews:

Related manuals for DI-804

Brands by name

Popular brands