D-Link DI-724P Page 11 Manual Download

Page: 11 / 101

DI-724U User’s Manual

D-Link Systems, Inc.

Getting Started

Getting Started

Please remember that

D-Link Wireless 108G

devices are pre-conﬁgured to connect

together, right out of the box, with their default settings.

For a typical wireless setup at home (as shown above), please do the following:

You will need broadband Internet access. (a Cable or DSL-subscriber line into

your home or ofﬁce)

Consult with your Cable or DSL provider for proper installation of the modem.

Connect the Cable or DSL modem to the DI-724U Wireless Broadband Router

(

see the printed Installation Guide included with your router

If you are connecting a desktop computer to your network, install the D-Link

Air

Plus

Xtreme G

DWL-G520 wireless PCI adapter into an available PCI slot

on your desktop computer. You may also install the DWL-520+, or the DWL-520.
(

See the printed Installation Guide included with the network adapter.

)

Install the D-Link DWL-G650 wireless Cardbus adapter into a laptop computer.

(

See the printed nstallation Guide included with the DWL-G650.

)

Install the D-Link DFE-530TX+ adapter into a desktop computer. The four

Ethernet LAN ports of the DI-724U are Auto MDI/MDIX and will work with both
straight through and cross-over cable. (

See the printed Quick Installation Guide

included with the DFE-530TX+.

)

1
2

3
4

5
6

Summary of Contents for DI-724P






































































































Search results

Summary of Contents for DI-724P

Reviews:

Related manuals for DI-724P

Brands by name

Popular brands

D-Link DI-724P, Manual

Search results

Summary of Contents for DI-724P

Reviews:

Related manuals for DI-724P

Brands by name

Popular brands