D-Link DI-524 - AirPlus G Wireless Router Manual Download

Page: 11 / 92

Please remember that wireless devices are pre-configured to connect together, right

out of the box, with their default settings.

You will need broadband Internet access (a Cable or DSL-subscriber line into

your home or office)

Consult with your Cable or DSL provider for proper installation of the modem

Connect the Cable or DSL modem to the DI-524 Wireless Broadband Router

(

see the printed Quick Installation Guide included with your router.

)

If you are connecting a desktop computer to your network, install the D-Link

Air

Plus

DWL-G510 wireless PCI adapter into an available PCI slot on your

desktop computer. You may also install the DWL-G510, or the DWL-520.

(See the printed Quick Installation Guide included with the network adapter.)

Install the D-Link DWL-G630 wireless Cardbus adapter into a laptop computer.

(

See the printed Quick Installation Guide included with the DWL-G630.

)

Getting Started

For a typical wireless setup at home (as shown above),

please do the following:

Setting up

a Wireless

Infrastructure

Network

Install the D-Link DFE-530TX+ adapter into a desktop computer. The four

Ethernet LAN ports of the DI-524 are Auto MDI/MDIX and will work with both

Straight-Through and Cross-Over cable.

(

See the printed Quick Installation Guide included with the DFE-530TX+.

)

Summary of Contents for DI-524 - AirPlus G Wireless Router





























































































Search results

Summary of Contents for DI-524 - AirPlus G Wireless Router

Reviews:

Related manuals for DI-524 - AirPlus G Wireless Router

Brands by name

Popular brands

D-Link DI-524 - AirPlus G Wireless Router, Manual

Search results

Summary of Contents for DI-524 - AirPlus G Wireless Router

Reviews:

Related manuals for DI-524 - AirPlus G Wireless Router

Brands by name

Popular brands