PSoC™ 6 Wi-Fi Bluetooth® pioneer kit guide, Document Number. 002-22677 Rev. *I
26
Kit operation
15.
PSoC™ 6 MCU program and debug header (J11):
This 10-pin header allows you to program
and debug the PSoC™ 6 MCU using an external programmer such as
. In
addition, an external PSoC™ 4, PSoC™ 5LP, or PSoC™ 6 device can be connected to this
header and programmed using KitProg3.
16.
CAPSENSE™ proximity header (J13):
A wire can be connected to this header to evaluate the
proximity sensing feature of CAPSENSE™.
17.
CAPSENSE™ slider (SLIDER) and buttons (BTN0 and BTN1):
The CAPSENSE™ touch-
sensing slider and two buttons, all of which are capable of both self-capacitance (CSD) and
mutual-capacitance (CSX) operation, allow you to evaluate the CAPSENSE™ technology. The
slider and buttons have a 1-mm acrylic overlay for smooth touch sensing.
18.
System power V
DD
selection switch (SW5):
This switch is used to select the PSoC™ 6 MCU
V
DD
supply voltage between a constant 1.8 V, a constant 3.3 V, and a variable 1.8 to 3.3 V. In the
variable 1.8 to 3.3 V mode, the PSoC™ Programmer software can control the voltage via
KitProg3.
19.
512-Mbit serial NOR flash memory (S25FL512S, U4):
The
capacity is connected to the serial memory interface (SMIF) of the PSoC™ 6 MCU. The NOR
device can be used for both data and code memory with execute-in-place (XIP) support and
encryption.
20.
PSoC™ 6 MCU user LEDs (LED8 and LED9):
These two user LEDs can operate at the entire
operating voltage range of PSoC™ 6 MCU. The LEDs are active LOW, so the pins must be
driven to ground to turn ON the LEDs.
21.
RGB LED (LED5):
This on
-
board RGB LED can be controlled by the PSoC™ 6 MCU. The LEDs
are active LOW, so the pins must be driven to ground to turn ON the LEDs.
22.
Wi-Fi and Bluetooth
®
module (LBEE5KL1DX-883, U6):
This kit features the on-board Wi-Fi
and Bluetooth
®
combination module to demonstrate the IoT features. LBEE5KL1DX is a Type
1DX module available with 2.4-GHz WLAN and Bluetooth
®
functionality. Based on Infineon
AIROC™ CYW4343W Wi-Fi & Bluetooth
®
combo chip, this module provides high-efficiency RF
front-end circuits.
23.
4-Mbit serial F-RAM (CY15B104QSN, U5):
This kit contains the CY15B104QSN
4-Mbit (512K × 8) Excelon™ F-RAM device, which can be accessed through the Quad SPI
interface, which is capable of Quad SPI speed up to 108 MHz but PSoC™ 6 MCU is limited to 80
MHz.
24.
Wi-Fi-Bluetooth
®
antenna (ANT1):
This is the on
-
board antenna connected to the Wi-Fi and
Bluetooth
®
module.
25.
VBACKUP and PMIC control selection switch (SW7, on the bottom side of the board):
This
switches the VBACKUP supply connection to the PSoC™ 6 MCU between VDDD/KITPROG3
and the SUPER CAP/PSOC 6. When VDDD/KITPROG3 is selected, the regulator ON/OFF is
controlled by KitProg3. When the SUPER CAP/PSOC 6 is selected, the regulator ON/OFF is
controlled by the PSoC™ 6 MCU.
26.
PSoC™ 6 USB Type-C connector (J28):
The USB cable provided with the PSoC™ 6 Wi-Fi
Bluetooth
®
pioneer kit can also be connected between this USB connector and the PC to use
the PSoC™ 6 MCU USB device applications.
27.
PSoC™ 6 MCU (CY8C6247BZI-D54, U1):
This kit is designed to highlight the features of the
PSoC™ 6 MCU. For details on PSoC™ 6 MCU pin mapping, see
28.
PSoC™ 6 USB Type-A connector (J27):
USB devices can be connected to this USB Type-A
connector and communicate with the PSoC™ 6 MCU USB host applications.
