CYPRES 2 User Manual Download Page 46

Page: 46 / 72

page 46

- CYPRES 2 User’s Guide -

8.2 Important notes for users

• CYPRES must not be used for

parascending

or paragliding/sailing.

• CYPRES cannot be used for

base jumps (jumps

from fixed objects), and must be switched off

prior to making a base jump.

• A

Student, Expert, Speed or Wingsuit CYPRES

will not activate if the aircraft is exited before it

reaches 1500 feet (450m) above the airfield and

intended DZ. In case of a

Tandem CYPRES

3000 feet (900m) must be reached.

• A two canopy scenario can be generated via a

CYPRES activation, if the main deploys too low.

• CYPRES is shielded against radio transmitter

signals. Extreme concerted efforts have been

taken to protect CYPRES 2 from „radio pol-

lution“. Although the extraordinary shielding

system of CYPRES 2 has been investigated

thoroughly, it is impossible to have 100%

protection. It is still recommended to avoid

strong radio transmitters. Please contact Airtec

if you have questions.

•

A release unit that has activated builds up a high

internal pressure and will remain pressurized.

Never attempt to open it by force. It can, how

ever, be stored safely for an indefinite period

of time, provided that it has not been damaged.

• The reserve container closing loop must be

under tension, caused by the pilot chute spring,

of at least 10 pounds (approx. 5 kg).

• A good reserve pilot chute is an important

safety factor. On systems with an internally-

mounted pilot chute, we recommend that

owners equip their rigs with one that has been

Airtec tested and subsequently qualified by the

h/c manufacturer in collaboration with Airtec.

Typically the rig manufacturer delivers these

pilot chutes with the rig. If in doubt, please

contact your h/c manufacturer.

• Don‘t forget: After water contact shut your

CYPRES 2 off immediately and change the filter.

• Make sure that the reserve closing loop passes

through the cutter’s passing hole.

Verify settings:

After changing settings as described in

chapter 4.4.2 and following, switch the unit ON and verify the

settings within the unit information sequence (see chapter 4.5)

Wrong settings can cause injury or death.

Summary of Contents for 2









































































Search results

Summary of Contents for 2

Reviews:

Related manuals for 2

Brands by name

Popular brands

CYPRES 2, User Manual

Search results

Summary of Contents for 2

Reviews:

Related manuals for 2

Brands by name

Popular brands