CYPRES 2 User Manual Download Page 23

Page: 23 / 72

- CYPRES 2 User’s Guide -

page 23

CYPRES can be assembled into rigs with exist-

ing setups. Please refer to the harness/container

manufacturer if in doubt.

It is necessary to place the

processing unit into the

pouch so that the cables lay flat on the bottom of

the pouch. Control unit cable and cutter cable(s)

must be placed without tension.

Excess cable is stowed in the flat part of the

pocket underneath the velcro-adjustable flap. If

you have to stow both the thinner cutter cable and

the thicker control unit cable, be sure to place the

thicker cable so that it lays on top of the thinner

one. Cables should be placed in a circle in order

to avoid twists. Always avoid pulling, bending,
twisting, or kinking the cables.

right

wrong

- cables not flat on

bottom

- unit is inserted up

side down

- thin cable on top

of thicker cable

- cable is bent

Inappropriate installation can result in inappropriate

container opening performance.

That can cause injury or death. Never install a CYPRES

by trial and error.

Removal of CYPRES can be done by the owner

without any problems. Do not pull on the cables,

instead push the processing unit, cutter and control

unit from their keepers.

Summary of Contents for 2









































































Search results

Summary of Contents for 2

Reviews:

Related manuals for 2

Brands by name

Popular brands

CYPRES 2, User Manual

Search results

Summary of Contents for 2

Reviews:

Related manuals for 2

Brands by name

Popular brands