Cynko
Met
T-104/4
T-104/5
Page 64
nut.
Turning the wheel, simultaneously tighten the castellated nut until the
wheel stops completely.
Unscrew the nut by 1/6 -1/3 turn, until covering the next groove on the
pin with a hole in the pivot. The wheel should turn without excessive
resistance, the nut cannot be tightened too much. It is not
recommended to use too strong pressure due to the deterioration
of the working conditions of bearings.
Secure the nut with a new cotter pin, and firmly press the hub cap.
The mentioned steps should be repeated checking the remaining wheels.
The wheel, after correct adjustment of the bearings should turn smoothly
without stops and perceptible resistance.
The soundness of bearings backlash has to be finally checked after driving a few
kilometers with the trailer controlling the degree of the hubs heat by hand.
The cause of the occurrence of significant resistance when turning the wheel,
and strong heating of the hubs apart from improper adjustment of the bearings
backlash can be contaminants in the lubricant or bearing damage. The above
symptoms require dismantling the wheel hub and removing the fault (replacement
of grease or bearings).
6.2
Brake adjustment.
Brakes regulation should be carried out if:
•
brakes of both wheels brake unevenly and / or non-simultaneously.
•
expander levers are not parallel to each other during braking.
•
a repair of the brake system was carried out.
Summary of Contents for T-104/4
