CyberPower OR1500PFCRT2U User Manual Download Page 7

 
1.  INPUT voltage meter:

 This meter measures the AC voltage that the UPS 

system is receiving from the utility wall outlet. The UPS is designed,   
through the use of automatic voltage regulation, to continuously correct   
output voltage to connected equipment to a safe 110/120 voltage output   
range. In the event of a complete power loss, severe brownout, or   
over-voltage, the UPS relies on its internal battery to supply consistent   
110/120 output voltage. The INPUT voltage meter can be used as a   
diagnostic tool to identify poor-quality input power. 

2.  OUTPUT voltage meter: 

This meter measures, in real time, the AC   

voltage that the UPS system is providing to the computer, such as   
normal line mode, AVR mode, and battery backup mode. (Note: The   
OUTPUT voltage meter shows the status of the battery backup outlets.) 

3.  ESTIMATED RUN TIME:

 This displays the run time estimate of the UPS with current battery capacity and 

load. 

4.  NORMAL icon: 

This icon appears when the UPS is working under normal conditions. 

5.  BATTERY icon: 

During a severe brownout or blackout, this icon appears and an alarm sounds (two short 

beeps followed by a pause) to indicate the UPS is operating from its internal batteries. During a prolonged 
brownout or blackout, the alarm will beep rapidly every 1/2 second (and the BATT.CAPACITY meter shows 
one 20% capacity segment shaded. The capacity depends on how much load added and the runtime left. 
You can setup the Low Battery Threshold through PowerPanel

®

 Business Edition software.) to indicate the 

UPS’s batteries are nearly out of power. You should save files and turn off your equipment immediately or 
allow the software to shut the system down. 

6.  AVR (Automatic Voltage Regulation) icon: 

This icon appears whenever your UPS is automatically 

correcting low AC line voltage without using battery power. This is a normal, automatic operation of your 
UPS, and no action is required on your part. 

7.  SILENT MODE icon: 

This icon appears whenever the UPS is in silent mode. The buzzer does not beep 

during silent mode until the battery reaches low capacity. 

8.  OVER LOAD icon: 

This icon appears and an alarm sounds to indicate the battery-supplied outlets are 

overloaded. To clear the overload, unplug some of your equipment from the battery-supplied outlets until 
the icon turns off and the alarm stops. 

9.  FAULT icon: 

This icon appears if there is a problem with the UPS, Contact CyberPower Systems at 

[email protected]

 for further help and support.   

F01: Battery Mode or Line Mode Overload fault 
F02: Battery Output Short fault 
F03: Charger Fault 
F04: Internal Fault 

10.  BATT. CAPACITY meter: 

This meter displays the approximate charge level (in 20% increments) of the 

UPS’s internal battery. During a blackout or severe brownout, the UPS switches to battery power, the 
BATTERY icon appears, and the charge level decreases. 

11.  LOAD CAPACITY meter: 

This meter displays the approximate output load level (in 20% increments) of 

the UPS battery outlets. 

 

Advanced LCD Functions Setup 

There are advanced LCD functions that can be setup through LCD Display button. (1) 

Mute

: Enable or disable 

any audible alarm caused by an event. (2) 

Sensitivity

: Control the sensitivity of the UPS to switch to Battery 

Mode by selecting UPS shutdown voltage range. The higher the sensitivity, the easier the UPS will switch to 
Battery Mode. (3) 

LCD Always On

: Keep the LCD always lit. (4) 

Self Test

: Perform a test in Line Mode to test 

Battery Mode function. It will return to Line Mode after the test is completed. (5) 

ESC

: Leave setup mode 

without changing any settings and return to LCD status display screen. 
For the 

Mute 

function, press Display button for 2 seconds to enable or disable audible alarm. When   

you enable audible alarm, the Silent icon is not lit. When you disable audible alarm, the Silent icon is lit. 
For the 

Sensitivity

,

 LCD Always On

Self Test

, and

 ESC

 functions, press Display button for 8 seconds to 

enter 

Function Setup 

screen. Press Display button once to choose between Sensitivity, LCD Always On, Self 

Test, and ESC Functions. When the function is chosen, press 2 seconds to enter 

Mode Setup 

screen. (or If the 

function you select is ESC, press 2 seconds and you will leave the Function Setup screen and return to LCD 

DEFINITION FOR ILLUMINATED LCD INDICATORS

 

 

 

 

Summary of Contents for OR1500PFCRT2U














Reviews: