Cyber Power PDU31001 User Manual Download Page 3

Page: 3 / 35

Model List

Switched Metered by Outlet Series

PDU81001

PDU81003

PDU81101

PDU81002

PDU81007

PDU81102

PDU81004

PDU81008

PDU81104

PDU81005

PDU81009

PDU81105

PDU81006

PDU81404
PDU81405

Metered by Outlet Series

PDU71001

PDU71003

PDU71002

PDU71007

PDU71004

PDU71008

PDU71005

PDU71009

PDU71006

Switched Series

PDU41001

PDU41003

PDU41101

PDU41002

PDU41007

PDU41102

PDU41004

PDU41008

PDU41104

PDU41005

PDU41009

PDU41105

PDU41006

PDU41404
PDU41405

Monitored Series

PDU31001

PDU31003

PDU31101

PDU31002

PDU31007

PDU31102

PDU31004

PDU31008

PDU31106

PDU31005

PDU31009

PDU31406

PDU31006

PDU3 1 1 1 4
PDU31414

Safety Precautions

Read the following before installing or operating the Power

Distribution Units (PDU):

•

Use only the supplied hardware to attach the mounting brackets.

•

The PDU must be plugged into a three-wire, grounded outlet

on a circuit that is protected by a fuse or circuit breaker. For

15A PDU series, please use a 15A circuit protector. For 20A PDU

series, please use a 20A circuit protector. For 30A PDU series,

please use a 30A circuit protector. Connection to any other

type of power outlet may result in a shock hazard.

•

Do not use extension cords or adapters with this PDU.

•

Never install a PDU or associated wiring or equipment during a

lightning storm.

•

Ensure that the power cord, plug, and socket are in good

condition.

To prevent the risk of fire or electrocution, this PDU should be installed
in a temperature and humidity controlled indoor area free of conductive
contaminants. Do not install this PDU where excessive moisture or heat
is present.

Summary of Contents for PDU31001



































Search results

Summary of Contents for PDU31001

Reviews:

Brands by name

Popular brands

Cyber Power PDU31001, User Manual

Search results

Summary of Contents for PDU31001

Reviews:

Brands by name

Popular brands