background image

 

- 12 -

controller  will  exit  the  user  mode  and will  indicate  the  temperature  of  the  water in 
the boiler 
 

CAUTION: If in the controller the hot water pump is turned off, in the user menu, after pressing 

OK, you can only read the set temperature value of the boiler thermostat. 

 

Table 1. Service parameters list 

Display 

Parameter 

Min 

Max  Step 

Factory 

default 

C 40 

Boiler desired temperature 

L 40  H 90 

1˚C 

L 40 

co C 

Central heating pump work when “C” (pump 

off when “-“) 

 

cu u 

“d” heating up – total bacteria control in hot 

water tank 

 

50˚ 

Water temperature in hot water tank 

 

 

 

 

End 

Exit from user mode after pressing OK 

 

 

 

 

 

1.  Boiler work temperature 

The boiler set temperature [C 40] – is the temperature which the controller will try 
to achieve in WORK mode. 
It is set by direct turning of the knob and is indicated by a short display. 
 

2.  Central  heating  pump  work  [co  C]  –  WINTER/SUMMER  mode  – 

character  “C”  indicates  that  the  central  heating  pump  is  working.  In  summer  time 
the  heating  can  be  turned  off  by  choosing  the  value  “-“  with  the  (-)  button  which 
means turning off the central heating pump. 
 

3.  Total  bacteria  control  in  the  hot  water  tank  –  heating  up  -  the 

controller allows to manually launch the total bacteria control process in the boiler. 
Choosing  the  “d”  value  with  (+)  button  starts  the  process  in  which  the  boiler  is 
trying to achieve the temperature of 75˚C in the hot water tank. In order to start the 
total bacteria control process the boiler should be in WORK mode (this mode can 
be  turned  on  by  START  button).  E.g.  [70˚d]  will  appear  on  the  display.  After 
reaching  75˚C  in  the  hot  water  tank  the  controller  will  return  to  its  state  before 
choosing this option. 

 

CAUTION: the total bacteria control function can switched on at night when the water from the 

hot water tank is not used to prevent the users from burn injury. 

 

4.  Water temperature readout in hot water tank [u50˚] – this parameter 

shows the measured temperature value in the hot water tank. 
 

5.  Exit  from  user  mode  –  choosing  the  [End]  on  the  display  and 

pressing OK button causes exit from the parameter setting. Exit from this mode will 
also occur if no button is pressed for 1 minute. 
 

Summary of Contents for Logica 100-110



























Reviews: