CVE JC300 Operation Manual Download Page 30

Page 30 

 

Symptoms 

Possible cause 

Corrective measure 

Motor will not start 

No fuel in the tank 

Fill the tank with the fuel type as 

described in this manual 

Dirty spark plug 

Clean or replace the spark plug 

Dirty filter 

Clean or replace the filter 

Dirty carburettor 

Visit the official technical service 

centre 

Stop 

Change the Start/Stop position 

Motor displaying irregular 

behaviour 

Dirty spark plug

 

Clean or replace the spark plug

 

Dirty filter 

Clean or replace the filter 

Rarified fuel 

Replacement for new fuel 

Started closed 

Open the starter 

Abnormal vibrations 

Sprockets/bearings 

worn. 

Visit the official technical service 

centre 

Abnormal noise 

Sprockets/bearings 

worn. 

Visit the official technical service 

centre 

7  Reference information 

This chapter contains technical and regulatory data, as well as other information. 

7.1  Machine warranty 

The machine’s warranty is subject to its own coverage and responsibility 

conditions. 
The motor’s guarantee is subsidiary, and as such, coverage pertains to the 

motor’s manufacturer, and the revision and maintenance of the spare parts is 

detailed in the motor’s manual delivered together with the machine at the time of 

purchase. 
The warranty for the rest of the machine is: 

12 months for private individuals 

The warranty does not cover an incorrect use of the machine or an inadequate 

maintenance. 
 

 

 

Summary of Contents for JC300
































Reviews: