CVE JC300 Operation Manual Download Page 13

Page 13 

 

Symbol 

Meaning 

 

WARNING 

The operation and maintenance of the machine must be performed 

exclusively by individuals qualified to that end. 

 

WARNING 

Do not use any accessories not supplied by the machine’s 

manufacturer or that has not been manufactured in line with the 

specifications issued by the machine’s manufacturer. 

 

WARNING 

Do not use the machine if it is not working correctly or if it has suffered 

any damages, for instance: 

• damages to the throttle trigger, 

• damages caused by blows or due to the machine having toppled or 

been dropped during transport or service, 

• unstable motor or hammer mechanism operation, 

• oil or fuel leaks. 

 

ENCLOSED LOCATIONS 

Do not use the Clavaestacas JC300 in enclosed or unventilated 

locations.  

In closed spaces, the combustion engine emits polluting, toxic gases 

that may cause dizziness, unconsciousness or even death. 

 

CAUTION 

The exhaust gas outlet must be free of blockages. 

U

SE OF FUEL AND FLAMMABLE LIQUIDS

 

When  refuelling  or occasionally using flammable liquids for cleaning or 

maintaining the machine, please observe these precautions to avoid the risk of 

fire or explosions. 
 

 

WARNING 

Fire hazard

. Upon refuelling or when carrying 

out maintenance, before starting the machine, 

please make sure there are no remnants of 

fluid, cloths or any other absorbent material or 

element used for cleaning. 

 

Summary of Contents for JC300
































Reviews: