background image

Spur Gear Assembly

Spur Gear Assembly

Spur Gear Assembly

Spur Gear Assembly

Spur Gear Assembly

5245     Qty 1
5-40 Locknut

1:1

-Parts for
 Bag G

1:1

2228     Qty 1
Spacer

2228             Qty 1
Slipper Eliminator

4881               Qty 1
81T 48P Spur Gear

5252                 Qty 1
4-40 x 1/4 BH Screw

- Press the 2228 Slipper Eliminator onto the Top
Drive Shaft so that the Roll Pin keys into the
grooves.
- Secure the assembly to the Top Shaft with the
2228 Spacer and the 5245 Locknut. Do NOT
overtighten the nut on the Top Shaft!
- Mount the 4881 Spur Gear so the flat side faces
AWAY from the transmission. Secure using (2)
5252 Screws.

2228

4881

5252

2228

5245

Transmission Mount

Transmission Mount

Transmission Mount

Transmission Mount

Transmission Mount

1:1

-Parts for
 Bag H

3229         Qty 2
Set Screw

1:1

1290               Qty 1
INT SE Trans Brace

1:1

3229        Qty2
Tall Body Post

3229      Qty 2
Post Collar

1202      Qty 1
Trans  Spacer

5264                 Qty 2
4-40 x 1/2 FH Screw

5253                 Qty 6
4-40 x 3/8 FH Screw

- Mount the 1202 Trans Spacer to the Chassis using the 5262
Screw where shown.
- Secure the Trans to the Chassis using (2) 5264 Screws thru the
1202 Trans Spacer as shown.
- Attach the 1290 Trans Brace to the Trans and Rear Bulkhead
using 5253 Screws.
- Mount the Trans Brace to the Trans and Rear Bulkhead using
5253 Screws.
-NOTE: Align the dogbone shafts into the outdrives of Trans as
you mount the trans!

3229                 Qty 2
8-32 x 1/2 FH Screw

1:1

Bag G

Bag G

Bag G

Bag G

Bag G

Bag H

Bag H

Bag H

Bag H

Bag H

5262                Qty 1
4-40 x 1/4 FH Screw

- Fasten the 1004 Rear Body Mount to
the 1290 Trans Brace in the holes as
shown.

- Slide Post Collar onto the Body Post
and secure using Set Screw.

- Attach 3228 Body Post to Rear
Body Mount using 3228 Screw.

3229

3229

3229

5217

5253

1290

1004

5217     Qty 2
4-40 Lock Nut

1202

5264

5262

1004             Qty 1
Rear Body Mount

Summary of Contents for 0912













Reviews: