2
PROGRAMMING THE ILG GRINDER
1. Turn
ON/OFF switch
to the OFF position.
2. Open the
lower front panel
by removing the holding screws.
3. Turn
ON/OFF switch
to the ON position. This turns on the components in the grinder and
timer board.
4. Locate the
timer
and move the
RUN-PROGRAM switch
to the PROGRAM position (see
illustration, right).
5. Locate the
grinding switch
indicating the amount of coffee to be ground (12, 24, or 36
cup - decaf or regular) on the front panel.
6. Press and hold the desired
grinding switch
for a precise amount of seconds to be equal
to the required grinding time. At the time the grinding switch is depressed, the following
will happen:
!
The original stored time will reset to zero and the timer will start a new count.
!
The auger and grinder motor will activate.
At the time of release of the grinding switch, the following will happen:
!
The timer is ready for adding or storing a preset time.
!
The auger will stop but the grinder motor will continue until the housing is cleared of ground coffee.
7. You can still add time to the same grinding switch. This "adding" function is active only for the grinding switch you are
programming at this time and until the RUN/PROGRAM switch is moved to the RUN position or
until you program a
different grinding switch. To add time, press and hold the same grinding
switch for the seconds you wish to add to this grinding switch.
8. Wait until the grinder motor stops, then switch the RUN/PROGRAM
RUN/PROGRAM
RUN/PROGRAM
RUN/PROGRAM
RUN/PROGRAM
switch
switch
switch
switch
switch to the RUN position. This will store the previously set times.
9. Turn ON/OFF switch
ON/OFF switch
ON/OFF switch
ON/OFF switch
ON/OFF switch to the OFF position.
10. Replace (remount) the Lower Front Panel.
PROGRAMMING THE
GRINDER
NOTE:
Time settings in
this table are only
approximate. Amounts
will vary with grind texture and
specific coffee bean. Weigh your
output, then make adjustments as
necessary
9
10
11
12
13
14
15
B
ILLUSTRATED PARTS
LIST
Grinder Motor
Grinder Motor
Grinder Motor
Grinder Motor
Grinder Motor
PARTS DIAGRAM
Hopper & Top Cover
Hopper & Top Cover
Hopper & Top Cover
Hopper & Top Cover
Hopper & Top Cover
ILGS Only
ILGS Only
ILGS Only
ILGS Only
ILGS Only
1
16
3
2
WARNING:
The next step will activate the 110 VAC circuit and some wires will be energized. Proceed with
CAUTION and avoid contact with "live" wires.
1.3
1.5
1.8
2.0
2.5
3.0
3.7
4
5
6
7
8
10
12
15
20
25
30
35
40
45
4.5
6.2
7.6
9.1
10.6
11.8
13.5
Seconds
Ounces
Seconds
Ounces
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
MOTOR CRUSHING GRINDER ASSY 120VAC
MOTOR, GRINDER 120VAC
CAPACITOR, COFFEE GRINDER ASSY
SHEAR DRIVE COFFEE GRINDER
SHEAR DISK
CAP, SHEAR DISK GRINDERS
COVER, GRINDER HOUSING W/LABEL
SCREW & THRUST PIN ADJUSTING ASSY
SPRINGBAFFLE LONG, NITRIC ACID COLORING
SPRING BAFFLE SHORT, NITRIC ACID COLORING
BAFFLE, SPOUT
SPOUT, GRINDER HOUSING
BURRS, SET CRUSH HIGH FLOW
SPRING, TENSION COFFEE GRINDER
WORM FEEDING ASSY CCG
WC-9135
WC-91022
WC-91026
WC-91024
WC-91025
WC-91016
WC-91017
WC-91015
WC-91029
WC-91027
WC-91028
WC-91023
WC-91045
WC-91021
WC-91020
ITEM
PART N°
5
1
2
8
6
4
7
3
B
A
