F
IND
OUT
MORE
ON
THE
WEB
.
WILBURCURTIS.COM
1
F
IND
OUT
MORE
ON
THE
WEB
.
WILBURCURTIS.COM
WILBUR CURTIS COMPANY
Montebello, CA 90640
Models Included
ILG
ILGS
CAUTION:
CAUTION:
CAUTION:
CAUTION:
CAUTION: Please use
this setup procedure
before attempting to use
this grinder. Failure to follow the
instructions can result in injury or
the voiding of the warranty.
WARNING
TO AVOID
SCALDING, Do not
remove brewcone whil
brew light is flashing.
ISO 9001 REGISTERED
C
InterLock Coffee Grinders - Instructions
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
WWW.WILBURCURTIS.COM
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an
authorized Wilbur Curtis service center.
•
Do NOT immerse the unit in water or any other liquid
•
To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be done
only by authorized service personnel.
•
Keep hands and other items away from hot parts of unit during operation.
•
Never clean with scouring powders or harsh implements.
Important Safeguards/Conventions
Conventions
Conventions
Conventions
Conventions
Conventions
W
W
W
W
WARNINGS –
ARNINGS –
ARNINGS –
ARNINGS –
ARNINGS – TTTTTo help a
o help a
o help a
o help a
o help avoid personal injur
void personal injur
void personal injur
void personal injur
void personal injuryyyyy
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factoryyyyy
QUICK ST
QUICK ST
QUICK ST
QUICK ST
QUICK STAR
AR
AR
AR
ART & SETUP
T & SETUP
T & SETUP
T & SETUP
T & SETUP
S E T U P
S E T U P
S E T U P
S E T U P
S E T U P
1. Install the grinder on a firm, level base in a location where it can be connected to a grounded electrical outlet of 120VAC,
rated at 15 amps minimum.
2. Test the unit by running some whole bean coffee through the grinder. If any problems are encountered, refer to the complete
troubleshooting section at www.wilburcurtis.com or call Technical Service at 800-995-0417.
CONNECTING THE INTERLOCK GRINDER
CONNECTING THE INTERLOCK GRINDER
CONNECTING THE INTERLOCK GRINDER
CONNECTING THE INTERLOCK GRINDER
CONNECTING THE INTERLOCK GRINDER
1. Place grinder near brewer.
2. Remove top cover of brewer.
3. Remove empty strain relief from hole labeled INTERLOCK in back of brewer. Pass end of grinder interlock cable through this
hole. On single head brewers plug the cable directly into timer WC-642. On dual head brewers plug interlock cable into the
timer interlock cable.
4. Place strain relief onto cable outside of brewer. Connection to Gem-312IL timer cable should be inside brewer. Use a plier to
squeeze the strain relief to slip it into the hole. Plug linecord into power outlet.
INTERLOCK OPERA
INTERLOCK OPERA
INTERLOCK OPERA
INTERLOCK OPERA
INTERLOCK OPERATING INSTR
TING INSTR
TING INSTR
TING INSTR
TING INSTRUCTIONS
UCTIONS
UCTIONS
UCTIONS
UCTIONS
1. Open the door on top of the grinder and fill with fresh whole bean coffee. Close the top door.
2. Place an empty Satellite on the warmer deck of the brewer and preheat it by switching on warmer.
3. Place a new paper filter into the brewcone.
4. Insert the brewcone into the basket holder arms on the grinder.
5. Press the appropriate grind switch (SMALL, MEDIUM or LARGE).
6. Allow the grind motor to completely stop before removing the brewcone. The
brew selection is now “Locked” in at the brewer and is indicated by the flashing
light on the InterLock brewer.
7.Transfer the filled brewcone to the brewer and press the flashing brew button.
Brew cycle is complete when the brew light stops flashing.
ADJUSTMENT FOR COARSE THROUGH FINE GRIND*
ADJUSTMENT FOR COARSE THROUGH FINE GRIND*
ADJUSTMENT FOR COARSE THROUGH FINE GRIND*
ADJUSTMENT FOR COARSE THROUGH FINE GRIND*
ADJUSTMENT FOR COARSE THROUGH FINE GRIND*
1. Empty hopper of coffee beans. Run grinder to clear grinding burrs of coffee.
2. Open housing cover to locate adjustment screw (8) and lock nut (7). Loosen lock nut.
3. Run motor during adjustment. Turning adjustment screw clockwise will result in a finer grind (if, while turning, you hear the
grinding burrs starting to touch, immediately, back off 1/8th turn). Turning counter
clockwise will produce a coarser grind.
4. With a screwdriver holding the adjustment screw in place, tighten the locknut.
5. Run some coffee beans through the machine to check the grind adjustment.
6. Replace front cover on machine.
*This adjustment may change the amount of ground coffee dispensed.
CHANGING A BROKEN SHEAR DISK
CHANGING A BROKEN SHEAR DISK
CHANGING A BROKEN SHEAR DISK
CHANGING A BROKEN SHEAR DISK
CHANGING A BROKEN SHEAR DISK
1. Unplug the power cord.
2. Empty the hopper of beans.
3. Take out the thumb screws (10) to remove the grind cap (6).
4. Pull out the grinding burr/feed worm assembly (2). The inner half of the grinding burr set
will remain in the housing.
5. Separate the shear cap (5) and shear drive (3). The snapped shear disk (4) should fall
out of it’s slot on the shear drive.
6. Inspect and clean housing (1) of any coffee or debris. Especially look for anything that may have broken the shear disk.
7. Re-insert the feed worm and grinding burr on to the motor shaft.
8. Push shear drive through burr/feed worm assembly and align large slot with tongue on the motor shaft.
9. Rotate burr/feed worm assembly to align slot with narrow slot on shear drive.
10. Insert a new shear disk into slot. Cover with the shear cap.
11. Replace grind cap and thumb screws.
W
W
W
W
W
ILBUR
ILBUR
ILBUR
ILBUR
ILBUR
C
C
C
C
C
URTIS
URTIS
URTIS
URTIS
URTIS
C
C
C
C
C
OMP
OMP
OMP
OMP
OMPANY
ANY
ANY
ANY
ANY
, I
, I
, I
, I
, I
NC
NC
NC
NC
NC
.....
2
1
6
5 4
3
8
7
10
