background image

2.4 Environmental

Operating temperature:

0°C to +50°C

Storage temperature:

-40°C to +85°C

Humidity: 

95% non-condensing at 38°C

Shock: 

SAEJ1378, 55g pulse at 9-13ms

Vibration: 

5g rms, 5-500 Hz, 2 hrs. per axis

Protection:

IP-54, including fan

2.5 Compliance

2.6 Battery Types

This charger is suitable for use with all 24V, 12 cell, rechargeable lead acid
batteries with capacities of approximately 200Ah. 

2.7 Charge Cycle Profile

The Model 1620 charger provides four different charge profiles: IVa (Off Mode,
see Figure 1), I

1

VI

2

a (Equalize Mode after Off Mode, see Figure 2), IV

1

V

2

(Float

Mode, see Figure 3), and I

1

V

1

I

2

V

2

(Equalize Mode after Float Mode, see Figure 4).

For definitions of the variables mentioned in this section, refer to Table 1.

Curtis 1620 Manual

page 2

MODEL ENCODEMENT

TECHNICAL SPECIFICATIONS

2.1 Electrical

2.2 Mechanical

Case: 

Aluminum alloy, black finish

End caps: 

Polycarbonate, black

Dimensions (mm): 

289L x 165.0W x 73.0H

Weight:

2.8kg

2.3 Connections

AC Power Inlet:

IEC 320/C14

Programming Port:

Molex 39-01-2040 For use with Curtis 
Instruments' Model 1311 handheld programmer only.

Pin

Function

1 Rx

SEC_RTN

3 Tx
4 +12V

Motor Controller Inhibit: 

Molex 39-01-4030 Capable of sinking up to 60mA
DC to ground.

Pin

Function

See wiring diagram

2 No 

connection

See wiring diagram

DC Power Output:

2 x M5 studs

Pin

Function

+

B+ output

B– output

Curtis 1620 Manual

page 1

1

2

1620uv-www/xx/yy-zzz

1620

u

v

- www /

xx

/

yy

- zzz

Model Cooling Sealing

Input Output Output  Series

Voltage

Voltage

Current

Number

F

S

120

24

20

001

Fan 

Sealed

120VAC

24VDC

20 Amps Consult Factory

cooled

for

230

additional options

230VAC

Input:

120VAC models

230VAC models

Voltage:

100-132VAC

180-264VAC

Frequency Range:

57-63Hz

47-63Hz

Input Current:

12Arms max. @ 100VAC/60Hz

4.5Arms max. @ 180VAC/50Hz

Output Voltage:

24VDC, nominal

Current:

0-20A

Max. Power:

480W

Radiated Emissions:

FCC Part 15, Class A

EN55011, Class A

Conducted Emissions:

FCC Part 15, Class A

EN55011, Class A

EN50082-1-1997

X

ESD:

EN61000-4-2:1995

Radiated Immunity:

EN61000-4-3:1995 +

A1:1998

Electrical fast transient:

EN61000-4-4:1995

Surge Immunity:

EN61000-4-5:1995

Conducted Immunity:

EN61000-4-6:1996

Power Frequency Magnetic Field:

EN61000-4-8:1993

Voltage dips and sags:

EN61000-4-11:1995

Harmonics:

EN61000-3-2:2000

Voltage fluctuations (flicker)

EN61000-3-3:1995

Safety

EN60335-1:1995
EN60335-2-29:1997

Summary of Contents for 1620









Reviews: