Curtis Dyna-Fog BLACKHAWK 2620 Instruction Manual Download Page 55

Page: 55 / 55

Dyna-Fog Offers a Complete Assortment of Sprayers and Foggers

PULSE-JET POWERED THERMAL FOGGERS:

From 0-120 GPH (0-453 LPH) output. Our complete line include

different models like the Superhawk, Golden Eagle, Trailblazer,

Falcon, Patriot, Blackhawk, Mister III, SilverCloud and Model

1200. Portable or Truck mounted machines. Different models are

available for Oil base or Water base formulations.

ELECTRIC ROTARY ATOMIZERS:

DYNA-JET L30:

State-of-the-

Art, Electric Rotary Atomizer

ULV Aerosol Generator. 12 VDC,

Light Weight, Truck mounted

Machine with FMI pump.

Optional Syncroflow Available.

DYNA-JET L15:

Drift Sprayer

for migratory pest control like

Locust. Flow Rate from 0 to 2 L/

min. Optional Radar Syncroflow.

ELECTRIC HAND-HELD ULV/MIST GENERATORS:

A Full line of electric cold fog applicators with 1-3

gallon tanks, available in 115 and 230 VAC.

COMBUSTION ENGINE DRIVEN ULV AEROSOL GENERATORS:

Truck mounted Units powered by 8, 9, 11, 18 and 20 HP four cycle, OHV

Gasoline Engines. Diesel versions also available. One, two, four and eight nozzle

configurations. Patented full remote control of boom functions (rotation of

turntable and angle of nozzles) available on certain models. Your choice of Gear,

Piston or Diaphragm pumping system. Pressurized system versions available for

specific international markets. Optional Automatic flow control “Syncroflow”

also available with Radar or GPS speed sensing. 25 cc and 40 cc two cycle

portable models are also available.

CURTIS

DYNA-FOG

Ltd.

"Innovators of Spraying and Fogging Technology Since 1947"

Contact Us For Your Nearest Distributor:

Ph: +1.317.896.2561

email: [email protected]

web: www.dynafog.com

17335 US. Highway 31 North

Westfield, IN 46074, USA

Rev.

-8-201

SuperHawk XP

Dyna-Jet L-30

Cyclone Ultra-Flex

LV-8

Hurricane ES

Dyna-Jet L-15

Summary of Contents for BLACKHAWK 2620
























































Search results

Summary of Contents for BLACKHAWK 2620

Reviews:

Related manuals for BLACKHAWK 2620

Brands by name

Popular brands

Curtis Dyna-Fog BLACKHAWK 2620, Instruction Manual

Search results

Summary of Contents for BLACKHAWK 2620

Reviews:

Related manuals for BLACKHAWK 2620

Brands by name

Popular brands