Cuppaz Sleek How To Use And Care For Download Page 39

Page: 39 / 44

info@ cuppaz.com

hotline: 852 2812 0428

8. Press and hold down buttons A and B while switching The Sleek on by pressing

the power on/off switch

Button B will light up, while warning light G and H blink alternately

YELLOW

and

RED

9. Press button B to start the descaling cycle.

The Sleek dispenses the descaling solution at intervals (5 doses with a 4-minute

pause between each one, for a total duration of about 25 minutes). During this step,

when the buttons must not be pressed, warning light G and H blink alternately

YELLOW and RED

10. When the first phase is over, button B lights up and the water tank is empty.

Carefully rinse out the water tank and refill it with fresh water (500ml).

11. Press B to start the rinse cycle.

The machine delivers the rinsing water until the water tank is empty. During this
phase, indicator lights

and

blink alternately

YELLOW and RED

. When the

rinse cycle is completed, the machine returns to the "first use" state.

Summary of Contents for Sleek













































Search results

Summary of Contents for Sleek

Reviews:

Related manuals for Sleek

Brands by name

Popular brands

Cuppaz Sleek, How To Use And Care For

Search results

Summary of Contents for Sleek

Reviews:

Related manuals for Sleek

Brands by name

Popular brands