manualshive.com logo in svg

Cub Cadet 900 series, Professional Shop Manual

Introducing the Motorola 900 Series – a versatile range of cutting-edge devices that deliver exceptional performance and connectivity. Simplify your experience with our comprehensive Quick Reference manual, available for free download at manualshive.com. Explore its extensive features and maximize the potential of your Motorola 900 Series device today.

Share
Download
background image

ELECTRICAL SYSTEM

93

Introduction

 

This chapter is divided into four sections:

•

Section 1:

 About this chapter and precautions

•

Section 2:

 Components                                    

This section will describe the location and opera-
tion of the electrical components on the tractor.  
Where appropriate, some disassembly or com-
ponent removal instructions will be included.

•

Section 3:

 Diagnostic Techniques                     

This section will cover basic tools, techniques, 
and methodology for diagnosing electrical issues 
on the tractor.  A lot of the information in this sec-
tion can be applied to other equipment.

•

Section 4:

 Schematics

Precautions

CAUTION: 

Before disconnecting any electrical 

component, take precautions to prevent the 
component or the wires attached to it from short-
ing out.  The most effective means of doing this 
is to disconnect the battery ground cable from 
the negative battery terminal.

CAUTION: 

Unless performing tests that require 

the electrical system to be in operation, discon-
nect the negative cable from the battery before 
doing any work to the electrical system of the 
tractor.

Components

The 900 series tractor uses a similar REV-TEC mow in 
reverse electrical system to the older Cub Cadet 1000 
series.

RMC Module

The RMC module contains electronic logic circuits. 
When diagnosing anything that is connected to the 
RMC module, a high impedance test light or a high 
impedance digital multi-meter (DMM) must be used. 
The amperage draw of a standard incandescent test 
light may over-burden some internal electronic circuits, 
burning-out the module.

NOTE: 

These tools are not outrageously expen-

sive or exotic. High impedance test lights (Thex-
ton model 125 is typical) can be purchased 
locally from stores like NAPA for under $30.00. 
Appropriate multi meters can be purchased for 
under $100.00, and are an invaluable tool for 
any competent technician.

•

It is typical when industries shift from electro-
mechanical to electronic controls that diagnosis 
shifts from tracing through a number of indepen-
dent circuits to checking the in-puts to and out-
puts from a central processor. This is similar to, 
but much less complex than the transition that 
the auto industry made with the conversion to 
fuel injection in the 1980s.

NOTE: 

The starter safety circuit has no connec-

tion to the RMC module.

•

The only one switch in the safety circuit that is 
capable of turning-off the engine works through 
the RMC module.

•

It is still important to be familiar with the workings 
of the individual components of the electrical 
system, but some of them can now be checked 
from a central point on the tractor. This makes 
life easier on the technician, frequently making it 
unnecessary to connect to difficult to reach 
switches in the preliminary stages of trouble-
shooting.

•

The function of individual safety switches can be 
seen as providing information “inputs” to the 
RMC module.

•

The next part of this section gives a detailed 
description of the electrical components on this 
tractor, their function in the system, and their 
physical location on the tractor. Armed with this 
information and the proper tools, a technician 
should be able to efficiently diagnose most elec-
trical problems.

CHAPTER 7: ELECTRICAL SYSTEM

Summary of Contents for 900 series







































































































































































































Reviews:

No comments

Related manuals for 900 series

Nakayama 020356 Manual preview
020356
Brand: Nakayama Pages: 78
Toro Power Max 39924 Operator'S Manual preview
Power Max 39924
Brand: Toro Pages: 32
Echo PB-603 Operator'S Manual preview
PB-603
Brand: Echo Pages: 24
Tarmo TAR1225 Instruction Manual preview
TAR1225
Brand: Tarmo Pages: 36
Ryobi R18EZBLW Manual preview
R18EZBLW
Brand: Ryobi Pages: 16
Poulan Pro 414741 Owner'S Manual preview
414741
Brand: Poulan Pro Pages: 32
Cub Cadet 31AH55TA596 Operator'S Manual preview
31AH55TA596
Brand: Cub Cadet Pages: 48
Husqvarna ST 327T Repair Parts Manual preview
ST 327T
Brand: Husqvarna Pages: 32
Husqvarna ST624E Parts Listing preview
ST624E
Brand: Husqvarna Pages: 12
Husqvarna ST724 Owner'S Manual preview
ST724
Brand: Husqvarna Pages: 40
Husqvarna ST261E Instruction Manual preview
ST261E
Brand: Husqvarna Pages: 76
Husqvarna ST 424 Operator'S Manual preview
ST 424
Brand: Husqvarna Pages: 136
Husqvarna ST 424T Operator'S Manual preview
ST 424T
Brand: Husqvarna Pages: 148
Stanley SPT500 Original Instructions Manual preview
SPT500
Brand: Stanley Pages: 20
MTD E600E Operator'S Manual preview
E600E
Brand: MTD Pages: 28
MTD 31AE6LFG700 Operator'S Manual preview
31AE6LFG700
Brand: MTD Pages: 28
MTD 31AH7S3G701 Operator'S Manual preview
31AH7S3G701
Brand: MTD Pages: 28
L.T. Rich Products Snowrator Zx4 Owner'S Manual preview
Snowrator Zx4
Brand: L.T. Rich Products Pages: 30

Brands by name

Popular brands

Load more brands