background image

INTRODUCTION

1

Professional Shop manual intent

This 

Manual

 is intended to provide service dealers with 

an introduction to the mechanical aspects of the new 
900 series tractor.

Detailed service information about the engine 
will be provided by the engine manufacturer, in 
most cases.

Disclaimer: 

This manual was written using first gener-

ation tractors. The information contained in this shop 
manual is correct at the time of writing. Both the prod-
uct and the information about the product are subject to 
change without notice.

About the text format:

NOTE: 

is used to point-out information that is 

relevant to the procedure, but does not fit as a 
step in the procedure.

CAUTION: 

Indicates a potentially hazardous sit-

uation that, if not avoided, may result in minor or 
moderate injury.  It may also be used to alert 
against unsafe practices.

DANGER: 

Indicates an imminently hazardous 

situation that, if not avoided, will result in death 
or serious injury.  This signal word is to be lim-
ited to the most extreme situations.

WARNING: 

 Indicates a potentially hazardous 

situation that, if not avoided, could result in 
death of serious injury.

Bullet points

: indicate sub-steps or points.

Disclaimer: 

This Professional Shop Manual is 

intended for use by trained, professional technicians.  

Common sense in operation and safety is 
assumed.  

In no event shall MTD or Cub Cadet be liable for 
poor text interpretation, or poor execution of the 
procedures described in the text.

If the person using this manual is uncomfortable 
with any procedures they encounter, they should 
seek the help of a qualified technician or Cub 
Cadet Technical Support.

Fasteners

Most of the fasteners used on the tractor are 
sized in fractional inches. Some are metric. For 
this reason, wrench sizes are frequently identi-
fied in the text, and measurements are given in 
U.S. and metric scales.

If a fastener has a locking feature that has worn, 
replace the fastener or apply a small amount of 
releasable threadlocking compound such as 
Loctite® 242 (blue).

Some fasteners like cotter pins are single-use 
items that are not to be reused. Other fasteners 
such as lock washers, retaining rings, and inter-
nal cotter pins (hairpin clips) may be reused if 
they do not show signs of wear or damage.  This 
manual leaves that decision to the judgement of 
the technician.

Assembly

Torque specifications may be noted in the part of the 
text that covers assembly, they may also be summa-
rized in tables along with special instructions regarding 
locking or lubrication. Whichever method is more 
appropriate will be used.  In many cases, both will be 
used so that the manual is handy as a quick-reference 
guide as well as a step-by-step procedure guide that 
does not require the user to hunt for information.

The level of assembly instructions provided will be 
determined by the complexity and of reassembly, and 
by the potential for unsafe conditions to arise from mis-
takes made in assembly.  

Some instructions may refer to other parts of the man-
ual for subsidiary procedures. This avoids repeating 
the same procedure two or three times in the manual. 

CHAPTER 1: INTRODUCTION

Summary of Contents for 900 series







































































































































































































Reviews: