background image

5

Never remove gas cap or add fuel while the engine 
is hot or running. Allow engine to cool at least two 
minutes before refueling.

Never over fill fuel tank. Fill tank to no more than 

½

 

inch below bottom of filler neck to provide space for 
fuel expansion.

Replace gasoline cap and tighten securely.

If gasoline is spilled, wipe it off the tractor’s fender. 
Move unit to another area. Wait 5 minutes before 
starting the engine.

Never store the machine or fuel container inside 
where there is an open flame, spark, or pilot light as 
on a water heater, space heater, furnace, clothes 
dryer, or other gas appliances. 

To reduce fire hazard, keep machine free of grass, 
leaves, or other debris build-up. Clean up oil or fuel 
spillage and remove any fuel soaked debris. 

Allow machine to cool at least 5 minutes before 
storing.

General Service:

Never run an engine indoors or in a poorly 
ventilated area. Engine exhaust contains carbon 
monoxide, an odorless and deadly gas.

Before cleaning, repairing, or inspecting, make 
certain the tines and all moving parts have stopped. 
Disconnect the spark plug wire and ground against 
the engine to prevent unintended starting. 

Never attempt to make adjustments or repairs to the 
machine while the engine is running.

Never check for leaks in the hydraulic lines with 
your hands. Hot, high pressure fluid can escape 
through a pin hole leak and cause serious injury by 
puncturing the skin and causing blood poisoning.

Muffler, engine and belt guards become hot during 
normal operation and can cause a burn. Hydraulic 
hoses, fittings and fluid also become hot during 
normal operation. Allow the machine, tiller 

attachment, and its related hardware time to cool 
before cleaning, repairing, or inspecting. 

Check the tine mounting bolts at frequent intervals 
for proper tightness. Also, visually inspect tines for 
damage (e.g., bent, cracked, worn etc.) Replace 
tines with the original equipment manufacture’s 
(O.E.M.) tines only, listed in this manual. “Use of 
parts which do not meet the original equipment 
specifications may lead to improper performance 
and compromise safety!” 

Tiller tines are sharp and can cause serious injury. 
Wrap the tines or wear gloves, and use extra 
caution when servicing them.

Keep all nuts, bolts, and screws tight to be sure the 
equipment is in safe working condition.

Never tamper with safety devices. Check their 
proper operation regularly. Use all guards as 
instructed in this manual.

After striking a foreign object, stop the engine, 
disconnect the spark plug wire and ground against 
the engine. Thoroughly inspect the machine for any 
damage. Repair the damage before starting and 
operating.

Check brake operation frequently as it is subjected 
to wear during normal operation. Adjust and service 
as required.

If the tractor or tiller attachment should begin to 
vibrate abnormally, stop the engine and check over 
the equipment immediately for the cause. Abnormal 
vibration is a warning of a problem.

Do not change the engine governor setting or 
overspeed the engine.

Observe proper disposal laws and regulations. 
Improper disposal of fluids and materials can harm 
the environment. 

Maintain or replace safety and instruction labels, as 
necessary.

Your Responsibility

Restrict the use of this power machine to persons who read, understand and follow the warnings and 
instructions in this manual and on the machine. 

The safety label on the equipment is reproduced 

below.

 Take a moment to study the label before operating the unit. Always maintain safety while 

operating or servicing the equipment.

Summary of Contents for 190-004





















Reviews: