background image

4

s

ectiOn

 2 — i

MpOrtant

 s

afe

 O

peratiOn

 p

ractices

Al

8. 

ways wear safety glasses, long pants, gloves, hearing 

protection and safety shoes when operating or 

maintaining this unit. Do not wear loose-fitting clothing 

and do not operate the machine for more than 2 hours 

without hearing protection.

Be 

9. 

aware of the mower and attachment discharge direction 

and do not point it at anyone. Do not operate the mower 

without the discharge cover or entire grass catcher in its 

proper place.
Do n

10. 

ot put hands or feet near rotating parts or under the 

cutting deck. Contact with the blade(s) can amputate 

hands and feet.
A missin

11. 

g or damaged discharge cover can cause blade 

contact or thrown object injuries.

Stop the 

12. 

blade(s) when crossing gravel drives, walks, or 

roads and while not cutting grass.
Watch fo

13. 

r traffic when operating near or crossing 

roadways. This machine is not intended for use on any 

public roadway.
Do not operate the machine while under the influence of 

14. 

alcohol or drugs.
Mow only in daylight or good artificial light.

15. 

Never carry passengers.

16. 

Back up slowly. Always look down and behind before and 

17. 

while backing to avoid a back-over accident. Be aware 

and pay attention to the safety system function that 

stops power to the  blades when driving in reverse. If not 

fuctioning properly, contact an authorized dealer for safety 

system inspection and repair. 

Slow down before turning. Operate the machine smoothly. 

18. 

Avoid erratic operation and excessive speed.
Disengage blade(s), set parking brake, stop engine and wait 

19. 

until the blade(s) come to a complete stop before removing 

grass catcher, emptying grass, unclogging chute, removing 

any grass or debris, or making any adjustments. 
Never leave a running machine unattended. Always turn 

20. 

off blade(s), place drive speed control pedals in neutral, 

set parking brake, stop engine and remove key before 

dismounting.
Use extra care when loading or unloading the machine into 

21. 

a trailer or truck. This machine should not be driven up or 

down ramp(s), because the machine could tip over, causing 

serious personal injury. The machine must be pushed 

manually on ramp(s) to load or unload properly.
Muffler and engine become hot and can cause a burn. Do 

22. 

not touch.
Check overhead clearances carefully before driving under 

23. 

low hanging tree branches, wires, door openings etc., 

where the operator may be struck or pulled from the 

machine, which could result in serious injury.
Disengage all attachment clutches, set the parking brake 

24. 

to the ‘

On’

 position and move the  speed control pedals to 

the neutral position before attempting to start the engine.
Do not attempt to mow through unusually tall, dry grass 

25. 

(e.g., pasture) or piles of dry leaves. Dry grass or leaves may 

contact the engine exhaust and/or build up on the mower 

deck presenting a potential fire hazard.

Never attempt to operate the traction unit without the 

26. 

mowing deck attached.
Keep the machine and especially the engine/pump and 

27. 

hydraulic components clean and free of grease, grass and 

leaves to reduce the potential for over heating and fire.
Use

28. 

 only accessories and attachments approved for this 

machine by the machine manufacturer. Read, understand 

and follow all instructions provided with the approved 

accessory or attachment. 

Data indicates that operators, age 60 years and above, are 

29. 

involved in a large percentage of riding mower-related 

injuries. These operators should evaluate their ability 

to operate the riding mower safely enough to protect 

themselves and others from serious injury. 
If situations occ

30. 

ur which are not covered in this manual, use 

care and good judgment. Contact your customer service 

representative for assistance.
Do not o

31. 

perate or start machines if there are fuel or oil 

leaks or spillage. Clean it up.
Do not stop or park machine over dry leaves, grass, debris, 

32. 

etc. that could be combustible.
Do not operate machines that have been damaged or have 

33. 

not been properly maintained. If the machine has been 

damaged, then have it repaired.
When looking for oil leaks, never run your hand over 

34. 

hydraulic hoses, lines or fittings. Never tighten or adjust 

hydraulic hoses, lines or fittings while the system is under 

pressure. If high-pressure oil penetrates the skin, the oil 

must be removed within a few hours by a doctor familiar 

with this form of injury or gangrene may result. Do not 

check for hydraulic leaks with any part of the body.
When operating this machine in the forward direction, do 

35. 

not allow the speed control pedals to return to the neutral 

position on their own. Always operate them smoothly and 

avoid any sudden movements of the pedals when starting 

or stopping.

Slope Operation

Slopes are a major factor related to loss of control and tip-over 

accidents which can result in severe injury or death. All slopes 

require extra caution. If you cannot back up the slope or if you 

feel uneasy on it, do not mow it. 
For your safety, use the slope gauge included as part of this 

manual to measure slopes before operating this machine on 

a sloped or hilly area. If the slope is greater than 20 degrees as 

shown on the slope gauge, do not operate this machine on that 

area or serious injury could result.

Do:

Mow across slopes, not up and down. Exercise extreme 

1. 

caution when changing direction on slopes.
Watch for holes, ruts, bumps, rocks, or other hidden 

2. 

objects. Uneven terrain could overturn the machine. Tall 

grass can hide obstacles.
Use slow speed. Choose a low enough speed so that you 

3. 

will not have to stop while on the slope. Avoid starting 

or stopping on a slope. If the tires are unable to maintain 

traction, disengage the blades and proceed slowly and 

carefully straight down the slope. 

Summary of Contents for S6031 Tank S

















































Reviews: