background image

9

Installation – Settings

DIP 3 

DIP 4  Installation height

Standard

OFF

OFF

45-55 cm – Normal

ON

OFF

56-70 cm – Normal

OFF

ON

45-55 cm – Increased alarm threshold*

ON

ON

56-70 cm – Increased alarm threshold*

DIP 3 and 4: Installation height / hob type

For hobs up to a width of 60 cm the sensor can be fitted 45-70 cm 
above the hob. Any lower and it might not comply with EN50615.
For wider hobs (up to 90 cm) the sensor must be fitted 65-70 above 
the hob to cover the full width.

* Increased alarm threshold 

Ceramic hobs give off a lot of radiant and residual heat, which can lead 
to false alarms, as the sensor also measures the heat outside the actual 
ring. Allowance can be made for this by increasing the alarm threshold 
for the smallest rings. 

NB: Increasing the alarm thresholds will reduce safety, because in certain 
cases the Cooker Guard will not differentiate between the smallest 
plates and radiant/residual heat.  Nor will the Cooker Guard comply with 
EN50615 in some cases when a higher alarm threshold is set. 

We would, however, recommend using cookware that covers the entire 
heating zone instead and turning the ring off BEFORE removing the 
cookware. 
NB: Does not apply to induction hobs.

DIP 1 

Audible alarm

Standard

OFF

Deactivates all sound

ON

DIP 2

Visual alarm

Standard

OFF

Deactivates all lights

ON

DIP 1: Audible alarm

DIP 2: Visual alarm

Summary of Contents for 6251650













Reviews: