CTB F4420125 Manual Download Page 5

Before installing and commissioning the Rondomat 3S, read the safety instructions, 
provisions and conditions carefully. This paragraph contains a number of general 
safety instructions. The installation of the device and remedying of any malfunctions 
should be performed by a certified electrical installer according to the applicable 
norms. The guarantee does not apply if this product is installed in any other way than 
is indicated by 

PigTek

 and if the product's motor has been opened and changes 

have been made to the product. 

Never install a damaged Rondomat 3S! Notify your supplier of any damages. 

Disconnect power before installation. 

Take precautions against electrostatic discharge (ESD) when working on the 
Rondomat 3S. Ensure the workplace is clean and dry.   

Use correct wires as shown in the connection diagrams. 

Make all wiring connections and check them before applying power. Incorrect 
connections can cause permanent damage. 

Never place the Rondomat 3S in a place where the weather has direct 
influence (not in the sun, not in places where the temperature can rise sharply 
etc.). 

Inspect the Rondomat 3S periodically for any damages. Notify your 
installation technician immediately of any damages. A damaged Rondomat 
3S is unsafe! 

Do not touch any of the Rondomat 3S moving parts. 

The Rondomat 3S must only be assembled and installed by personnel with 
the relevant technical qualifications who have read and understood these 
manual. The safety instructions must always be observed. 

Summary of Contents for F4420125


















Reviews: