background image

SOOGM-16V

Radio Replacement with OnStar, SWC Retention and

Video Switcher for GM LAN 29 Bit Vehicles

RADIO REPLACEMENT

SWC RETENTION

+

R

INTERFACING SOLUTIONS

Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA  91335

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.122518

For vehicles with a factory reverse camera installed, the factory camera module must be powered up to enable the 

forced view feature of the SOOGM-16V. Connect the Reverse Gear Wire (RED/WHITE) on the SOOGM-16V harness 

to the reverse camera power wire located on the reverse camera module or BCM. The factory reverse camera 

module or BCM can be found in different locations in the vehicle depending on the year and model. The chart below 

will aid in locating the reverse camera module or BCM. 

Use a 1N4001 diode to isolate the factory reverse camera power wire. See diagram below.

REVERSE WIRE CONNECTION:

Factory

Reverse

Camera

Module

Reverse Gear Wire on

SOOGM-16V (RED/WHITE)

Factory Reverse Camera Wire

(BLUE or Light Green)

1N4001 Diode

YEAR/MODEL

LOCATION

WIRE COLOR

2007 – 2008

All Models

Under front passenger 

seat

BLUE

Pin 1 of 8-pin Connector

2009

Avalanche, Escalade, 

Suburban, Tahoe, Yukon

2011

Tahoe

Junction block next to the 

steering column

(See wiring connection

diagram on the next page)

BLUE

Pin 8 of Gray Connector

DARK BLUE

PIN 5 of Gray (X11) Con-

nector

2009

Hummer H2

BCM to the left of the 

steering column

BLUE

Pin 4 of Brown Connector

2009

Acadia, Enclave, Outlook, 

Traverse

BCM to the left of the 

steering column

BLUE

Pin 3 of Gray Connector

2009

Silverado, Sierra

BCM to the left of the 

steering column

LIGHT GREEN

Pin 2 of Connector 7

2009

Vue

BCM under the radio

LIGHT GREEN

Pin 2 of Connector 6

4 of 6

Summary of Contents for SOOGM-16V







Reviews: