background image

SOOGM-16V

Radio Replacement with OnStar, SWC Retention and

Video Switcher for GM LAN 29 Bit Vehicles

RADIO REPLACEMENT

SWC RETENTION

+

R

INTERFACING SOLUTIONS

Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA  91335

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

INSTALLATION DIAGRAM:

AFTERMARKET

RADIO

Reverse Gear            Red/White

Parking Brake        Yellow/Black

Illumina�on (+)                  Orange

+12V Constant                    Yellow

+12V ACC                         Red

Ground                       Black

Right Front (+)                        Gray

Right Front (-)            Gray/Black

Le� Front (+)                     White

Le� Front (-)         White/Black

Right Rear (+)                     Violet

Right Rear (-)         Violet/Black

Le� Rear (+)                    Green

Le� Rear (-)        Green/Black

TO FACTORY

HARNESS

24-Pin

Connector

8-Pin

Connector

BOSE

NON BOSE

10-Pin

Connector

SWC DIP   SWC   CAM

1     2     3      4

ON

Video Out
Front Camera
Rear Camera

To OEM Camera

Harness

Brown 16-Pin

Connector

VIDEO HARNESS

Chime Volume

Adjustment

1     2     3

ON

VR Activation

for OnStar (set DIP#1 to ON)

4-Pin

Connector

Cap or insulate if

not being used

3.5MM SWC CABLE

Plug in the 3.5MM SWC cable to the 4-pin port

on the module. See “DIP SWITCH SETTINGS” section.

LIN BUS (Green/Black)

JVC/Kenwood (Blue / Yellow)

Insulate if not

being used

If the vehicle is equipped with a Bose system, the SOOGM-16V 

has a built-in Bose adaptor that allows the proper audio input 

gain from the aftermarket radio to the Bose amplifier. To use 

this feature, plug in the male 8-pin connector on the harness to 

the GRAY female 8-pin connector on the SOOGM-16V module. 

The module is also labeled “Bose” and “Non Bose” to avoid 

confusion. (see picture below)

If the vehicle is NOT equipped with a Bose system, plug in 

the male 8-pin connector to the BLACK female 8-pin on the 

SOOGM-16V module.

Bose

Connection

Non Bose

Connection

SELECTING THE AUDIO SYSTEM:

2 of 6

rev.122518

Summary of Contents for SOOGM-16V







Reviews: