background image

INSTALLATION & OPERATION MANUAL 10070 REV 0 (04/21)

 PAGE

4    

OF 32

G

as

 F

ired

 S

team

 T

ilting

 K

ettles

S

ervice

 C

onnections

S

ERVICE 

C

ONNECTIONS

GAS CHARACTERISTICS

DIMENSIONS

* For use on non-combustible floors only.

SERVICE CONNECTIONS

 – GAS CONNECTION: Supply Gas through 3/4” pipe.  A gas shut off valve must be installed in supply piping convenient and adjacent to appliance.

 – ELECTRICAL CONNECTION : Unless otherwise specified, field wire electrical connection to be 120 volts, 60 Hz, 1 phase with grounding wire.  Unit 

furnished with 6’ cord and 3 prong plug.  Total maximum amps 4.0.

 – COLD WATER: 3/8” (10 mm) tubing to faucet (optional)
 – HOT WATER: 3/8” (10 mm) tubing to faucet (optional)

Model

Capacity

Units

A

B

C

D

E

F

G

H

J

K

L

M

N

GLT-20

20 gallons

(76 liters)

in

(mm)

20”

(508)

48.13”

(1222)

40.63”

(1032)

19”

(483)

40.13”

(1019)

76.5”

(1943)

16.5”

(419)

24”

(610)

11”

(279)

22”

(559)

40.5”

(1029)

18.38” 

(467)

25.5”

(648)

GLT-30

30 gallons

(114 liters)

in

(mm)

26”

(660)

55.25”

(1403)

43.63”

(1108)

16.5”

(419)

39”

(991)

73.75”

(1873)

15.5”

(394)

22.25”

(565)

7.5”

(191)

21”

(538)

38.13”

(968)

17.88” 

(454)

28.5”

(724)

GLT-40

40 gallons

(152 liters)

in

(mm)

26”

(660)

55.25”

(1403)

43.63”

(1108)

16.5”

(419)

43.25”

(1099)

76”

(1930)

15.5

(394)

22.25”

(565)

7.5”

(191)

23”

(584)

42.5”

(1080)

22.13” 

(562)

28.5”

(724)

GLT-60

60 gallons

(227 liters)

in

(mm)

30”

(762)

59”

(1499)

45.63”

(1159)

17.88”

(454)

43.88”

(1115)

82”

(2083)

19.5”

(495)

22.25”

(565)

5.5”

(140)

23”

(584)

45.5”

(1156)

24.75” 

(629)

30.5”

(775)

Model

Gas Supply

Shipping 

 

Weight

Minimum Clearance

BTU/HR.

kW/HR.

Supply Pipe Pressure (W.C.)

GLT-20

80,000

23.4

Natural

6”-14”  

(152-356 mm)

Propane

11”-14”  

(279-356 mm)

700 lbs. [318 kg]

SIDES

BACK

0” [0 mm]

4” [102 mm]

GLT-30

100,000

29.3

900 lbs. [408 kg]

GLT-40

100,000

29.3

930 lbs. [422 kg]

GLT-60

120,000

35.2

1142 lbs. [51 kg]

As continued product improvement is a policy of Crown, specifications are subject to changge without notice.

Summary of Contents for GLT-20

































Reviews: