background image

Fig.19

ATTENTION!

When opening the autoclave for cooling, observe

the correct position of the door in the picture. The autoclave

Vitale Plus 

dries with the door closed

, its opening is only

necessary to speed up the cooling process of the 

instruments/articles sterilized).

Upper view

CRISTÓFOLI

A U T O C L

A V E S

I N S T R U C T I O N    M A N U A L

When the depressurization is over, the drying stage will begin automatically, the display will show the message 

drying

 

and the temperature of the chamber. 

The autoclave Vitale Plus dries with the door closed

. At the end of the drying 

process, the autoclave will beep 3 times and the display will show the message 

cooling

. At this moment, the operator 

must  open  autoclave  door  and  leave  it  ajar  to  accelerate  the  cooling  process  of  the  sterilized  articles.  Within  5 
minutes  the  autoclave  will  beep  continuously  and  the  display  will  show  the  message 

cycle  concluded

,  only  then, 

remove the sterilized articles. Press the 

CANCEL

 key to return to the program selection mode.

ATTENTION!

 Even after the beeps that indicate the conclusion of the cycle, the contents of the chamber will still be hot. 

Never

  touch  the  internal  parts  of  the  autoclave  directly chamber,  trays,  materials,  etc.

ait  for  them  to  be 

  (

)  when  hot,  w

cool enough before handling. R

 gloves for thermal protection

emember to use safety

.

h

g

T

 

CANCEL

 key for 2 seconds. It’s not recommended to disconnect 

urn the autoclave off after use. To do that, press the

the equipment from the outlet so that it is not necessary to adjust the time and date again.

15

 

For the 

Unwrapped Instruments

 cycle, after the depressurization, the autoclave will show the message:

 

 

 

 

Press the 

Start

 key to proceed with drying. By pressing the 

CANCEL

 key, there will be no drying, 

(flash sterilization). 

Important!

 This option must be used only for immediate use of the instruments.

dry ?

st : yes   Can : no

Note:

 For the autoclave model Vitale Plus 21, when selecting the 

Surgical Kit

 cycle, the surgical case must be placed in 

the central tray. For the Vitale Plus 12, the case (which must be compatible with the size of the autoclave) must be put on 
the top tray.

Summary of Contents for Vitale Plus 12



























Reviews: